Genie 1500 Important Safety Instructions, WARNINGToreducetherisk ofsevereinjuryordeath, See page

3MAINTENANCE & TROUBLESHOOTING

If you have any questions, please do not hesitate to contact customer service at: 1-800-35-GENIEor visit www.geniecompany.com.

IMPORTANT SAFETY

INSTRUCTIONS

WARNING:Toreducetherisk ofsevereinjuryordeath

1.	READ AND FOLLOW ALL INSTRUCTIONS.
2.	Never let children operate or play with the door controls.
	Keep the remote away from children.
3.	Always keep the moving door in sight and away from people
	and objects until the door is completely closed. NO ONE
	SHOULD CROSS THE PATH OF THE MOVING DOOR.
4.	NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.
5.	Test opener monthly. The door MUST reverse on contact
	with a 1-1/2" high object (or a 2" x 4" board laid flat) at the
	center of the doorway on the floor. After adjusting either the
	force or the limit of travel, retest the door opener. Failure to
	adjust the opener properly may cause severe injury or death.
6.	When possible, use the emergency release only when the
	door is closed. Use caution when using this release with the
	door open. Weak or broken springs are capable of increasing
	the rate of door closure and increasing the risk of severe
	injury or death.
7.	KEEP DOORS PROPERLY BALANCED. See your garage door

Safe-T-Beam® (STB) SYSTEM CHECK

Check that both the RED and GREEN LEDs are ON steady. This indicates the system is working properly. If both LEDs are not ON steady, check the appropriate items below.

ss34" 2ED ,%$ FLASHES

–Check for obstruction.

–Check alignment.

–Verify wire routing from STBs to STB connection in powerhead.

–Check for signal interference from another. Safe-T-Beam® unit (For multiple door installations).

ss .O 34"O2ED3OR 'reen LED displayed.

–Check wiring and wire connections.

If the system appears to be working properly, perform the check as follows:

1.Start the door closing.

2.Pass on object through the beam, the door should stop and reverse to the fully open position.

DOOR BALANCE (SPRING TENSION)

Perform the check as follows:

ssWith the door closed, pullrelease handle DOWN and let go to release door carriage assembly from drive system.

ssRaise and lower the door manually—it should move freely and smoothly.

ssRaise door manually about 3’ to 4’ feet and let go.

Owner’s Manual. An improperly balanced door increases the

risk of severe injury or death. Have a trained door system

technician make repairs to cables, spring assemblies, and

other hardware.

8. SAVE THESE INSTRUCTIONS.

3’ - 4’

Sectional Door

3’ - 4’

One-Piece Door

WARNING

sGarage door hardware (springs, cables, brackets, pulleys, etc.) are under extreme pressure and tension.

sDO NOT attempt to repair or adjust door springs or any hardware, and DO NOT OPERATE garage door automatically or manually if door is improperly balanced or springs are broken.

–CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

ROUTINE MONTHLY MAINTENANCE

Basic monthly maintenance tasks.

sContact reverse

sSafe-T-Beam® System Check

sDoor balance

sLubricate Door Hardware

CONTACT REVERSE TEST

See page 5.

WARNING

Use wall console supplied with opener. Other approved wall consoles may be available. Unapproved or incompatible wall consoles can cause the opener to operate unexpectedly.

–Door should remain stationary or move very slowly.

–If door moves quickly, CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

ss#LOSE THE DOOr.

ssVerify shuttle release lever is in the ENGAGED (up) position (pull release handle toward opener and let go).

OPENER

ENGAGED

DISENGAGED

–Operate door using a remote or wall console.

–Door will re-attach itself to carriage assembly.

LUBRICATE DOOR HARDWARE

Lubricate door rollers, bearings and hinges:

ssUse silicone lubricant or lightweight oil.

9/2011 ©2011 The Genie Company 8