2PROGRAMMING LIMITS
WARNING
sMake sure doorway is in view and clear of obstacles and people to avoid injury or damage to property.
sDO NOT operate this unit from wall console before LIMITS and FORCE are set. Severe damage to the opener can occur.
sThe bullet MUST be engaged to carriage BEFORE setting limits. See Installation Poster (if provided) or call Customer Service at
NOTE: If bullet has NOT been engaged to the carriage, do so now. See page 9.
Please note that there is a 30 second timeout between each programming step.
If you see two flashing RED LEDs, you have initiated a timeout.
In the event of a timeout you must restart at beginning.
TRAVEL LIMITS
DOWN LIMIT
ACTION | LED INDICATION/RESULT | ||
1 | Long LED turns Blue, then flashes. | ||
Press & hold |
|
| |
2 seconds or until | OFF | OFF | |
LEDs react. Release. | |||
BLUE | FLASHING |
2Press & hold
until door is fully |
| DOOR FULLY OPEN |
|
|
closed. Then release. |
|
|
|
|
3 Press & | PROGRAM | Both BLUE then LEDs Off confirms limit set. | ||
Release. |
|
|
|
|
| SET | BOTH FLASH BLUE |
| OFF |
|
| OFF | ||
|
| During the initial setting |
| |
|
| of the limits- the LEDs will | RED RED | |
|
| turn to | ||
UP LIMIT |
|
|
|
|
4 |
| Long LED turns Blue, | Then Long LED OFF | |
Press & hold |
| Round LED OFF. | Round LED Flashing. | |
2 seconds or until |
| OFF |
| FLASHING |
LEDs react. Release. |
|
| ||
|
| ON | OFF |
5Press & hold
| until door is fully |
| DOOR FULLY CLOSED |
|
| open. Then release. |
|
|
|
6 | Press & | PROGRAM | Both BLUE then LEDs Off confirms limit set. | |
|
|
|
| |
| Release. |
|
|
|
|
| SET | BOTH FLASH BLUE | OFF |
|
| OFF |
DOOR LIMITS ARE SET
SET FORCE NEXT
FORCE CONTROL
ACTION | INDICATION/RESULT |
1ON WALL CONSOLE
Press & | Door fully closes. | |
Release |
| |
Open/Close |
| |
button. |
| |
2 | Door fully opens. | |
Press & | ||
| ||
Release |
| |
Open/Close |
| |
button. |
|
FORCE CONTROL IS SET
CONTACT REVERSE TEST
WARNING
A moving door can cause serious injury or death.
1.Keep people clear of opening while door is moving.
2.Do NOT allow children to play with opener, including wall console, remote, or wireless keypad.
3.During programming, door opener could begin to run, so stay away from moving door and its parts.
The Force and Limit settings MUST be COMPLETED before performing Contact Reverse Test.
1. Test.
ACTION | INDICATION/RESULT | |
1 |
| |
Press & | DOOR OPENS. | |
Release the | ||
| ||
Open/Close |
| |
button. |
| |
2 |
|
Place a 2" x 4" board (laid flat) under center of door opening.
3 | DOOR CLOSES. | |
Press & | ||
s When door contacts board, | ||
Release the | it must stop and reverse direction | |
Open/Close | (within 2 seconds) to the fully | |
button. | open position. |
2.Adjustment, if needed.
ssIf the door stops before it contacts the board
or it does not reverse, it may be due to an improperly set down limit. Repeat TRAVEL LIMITS program and Test again. Repeat as needed until door passes test. For further help refer to Maintenance &Troubleshooting, page 13.
Once the Contact Revese Test is complete, continue with programming Remotes.
5 | ©2011 The Genie Company | 9/2011 |