OPTIONAL PROGRAMMING
IntelliCode® 1 or 2 wireless keypad
ACTION | LED INDICATION/RESULT |
1Enter your PIN
on the wireless keypad.
| 2 |
| Press & Hold for | ROGRAM |
|
|
|
|
|
|
|
| |
|
|
| 2 seconds or until |
|
|
|
|
|
| round LED turns blue | SET | BLUE | OFF |
|
|
| then OFF. | OFF | PURPLE | |
|
|
|
| |||
|
|
| Then Long LED flashes purple. |
| FLASHING | |
|
|
|
|
| ||
4 |
| Press & release 2 times. |
| Both LEDs OFF confirms communication | ||
|
| is established with operator. | ||||
|
|
|
|
| ||
|
|
|
|
| OFF | OFF |
|
|
|
|
|
| |
| 5 |
| Press & |
| Door moves. | |
|
|
| release |
|
|
|
Genie® Intellicode® 2 Wireless Keypad comes with a complete set of instructions.
LOST OR STOLEN REMOTE - CLEARING MEMORY
| ACTION |
| LED INDICATION/RESULT | ||
1 | Press & hold | PROGRAM | Round LED BLUE then OFF, Long LED FLASHING | ||
|
|
| |||
| 2 seconds. |
|
| BLUE | OFF |
| Release. | SET | OFF | PURPLE | |
|
| ||||
2 |
|
|
|
| FLASHING |
Press & hold |
|
|
|
| |
| BOTH open |
|
|
|
|
| and close |
|
| BOTH BLUE |
|
| buttons |
|
|
| |
| together. |
|
| FLASHING |
|
|
|
|
|
| |
3 | Release. |
|
|
|
|
|
|
|
| OFF |
|
|
|
|
| OFF |
|
REMOTE CLEARED FOR REPROGRAMMING
(To verify memory is
not respond.)
NOTE: Clearing remotes from powerhead memory will clear ALL programmed remotes and wireless keypad.
All remotes and wireless keypads must be reprogrammed.
Your door opener will no longer recognize any signal received from a missing remote.
WALL CONSOLE - OVERVIEW
This opener has a Serial Number sticker in which the serial numbers begin with 10 or higher.
MODEL AC SR3 | THE GENIE COMPANY |
FCC ID: B8Q AC SR3 | Residential Door Operator |
IC: | 120V. 60HZ. 5A |
S/N:10XXXX XXXXXXX |
|
FOR H LP CAL
Wall consoles from other manufacturers may not work with openers of these serial number groups. Genie® Series I wall buttons and Series II wall consoles will not work with openers of this serial number group.
Use only the Series III wall console provided with this unit. Wall console has three buttons and one indicator light.
Indicator Light
Indicator light will display Red when wall console is properly wired and
Open/Close Button
Use this button to open or close garage door. When
Independent Light Control Button
Use this button to turn powerhead lights ON. Powerhead lighting will remain ON until this button is pressed again or a door action has been completed. Note: If opener has a Motion Detector sensor, it will keep powerhead lights ON as long as motion is detected
Sure-Lock™ Button
When
sPress and hold for 5 seconds (or until Indicator Light flashes) to activate
sPress and release to turn
Open/Close Button
Open and closes door from inside garage.
–LOCK disables controls after door is completely closed.
– UNLOCK allows controls to work normally
Indicator Light
Red indicator light is always ON
When Sure-Lock™ is ON the indicator light flashes
Independent Light Control Button
Controls door opener lights from inside garage
Tip: If the Wall Console is energized (LED ON), but the door does not
respond to the | FROM STBs |
|
|
|
| FROM STBs | |||
|
|
|
| FROM WALL |
| FROM WALL | |||
OPEN/CLOSE |
|
|
|
| CONSOLE |
| CONSOLE | ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
the Console is |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
wired to the |
|
|
|
|
|
|
|
| NOT NOT |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| USED USED | |
BWC terminals |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
on the powerhead. |
|
|
|
|
|
|
|
|
|
| STB | BWC IWC |
| STB BWC IWC | |||||
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
7 | ©2011 The Genie Company |