Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie Z-60, Z-34 manual Lifting Instructions, Chassis Lifting Points, Observe and Obey

Models: Z-60, Z-34

1 41

Page 38

Operator's Manual	Sixth Edition · Second Printing

TRANSPORT AND LIFTING INSTRUCTIONS

Observe and Obey:

Only qualified riggers should rig and lift the machine.

Be sure the crane capacity, loading surfaces and straps or lines are sufficient to withstand the machine weight. See the serial plate for the machine weight.

Lifting Instructions

Fully lower and retract the boom. Move the jib perpendicular with the ground. Remove all loose items on the machine.

Use the turntable rotation lock to secure the turntable.

Determine the center of gravity of your machine using the picture on this page.

Attach the rigging only to the designated lifting points on the machine. There are four lifting points on the chassis.

Adjust the rigging to prevent damage to the machine and to keep the machine level.

Chassis

Lifting

Points (2)

4 ft 2 in	Chassis
1.27 m	Lifting
	Points (2)
	3 ft 4 in
	1.02 m

Z-60/34

Part No. 1000209

Page 38

Image 38

Genie Z-60, Z-34 manual Lifting Instructions, Chassis Lifting Points, Observe and Obey

Contents

Sixth Edition Second Printing Part No. with Maintenance InformationOperator’s Manual Contents Contact usDo Not Operate Unless Safety RulesDanger 1 Avoid hazardous situationsElectrocution Hazards Tip-overHazardsSixth Edition · Second Printing Fall Hazards Explosion and Fire Hazards Collision HazardsComponent Damage Hazards Weld Line to Platform Safety if equippedDamaged Machine Hazards Bodily Injury HazardsElectrocution Hazard Battery Safety Burn HazardsExplosion Hazard Decal LegendControls Platform Control PanelSixth Edition · Second Printing Ground Control Panel Legend 2Always perform a pre-operationinspection Pre-operationInspectionFundamentals Do Not Operate UnlessPre-operationInspection Observe and Obey MaintenanceMaintenance Symbols Legend Check the Engine Oil LevelCheck the Hydraulic Oil Level Check the Batteries Check the Tire PressureScheduled Maintenance 3Always perform function tests prior to use Function TestsAt the Ground Controls Test Emergency StopTest the Tilt Sensor At the Platform ControlsTest the Machine Functions Test Auxiliary ControlsTest the Horn Test the Foot SwitchTest the Hydraulic Oil Return Filter Test the SteeringTest the Drive Enable System Test Drive and BrakingTest Auxiliary Controls Test Limited Drive SpeedTest the Lift/Drive Select Function if equipped 4Inspect the workplace Workplace InspectionWorkplace Inspection Do Not Operate UnlessDo Not Operate Unless Operating Instructions5Only use the machine as it was intended FundamentalsGasoline/LPG models Starting the EngineEmergency Stop Diesel modelsOperation from Platform Auxiliary ControlsOperation from Ground To Position Platformrun rise Driving on a slopeTo determine the slope grade Drive Speed Select Drive EnableGenerator if equipped Engine Idle Select rpmCheck Engine Light if equipped Machine Not Level Indicator Light if equippedPlatform Overload Indicator Light if equipped Fall ProtectionPart No DecalsInspection for Decals with Words Decal DescriptionOperators Manual Ground Controls Side Chassis Platform Engine SideSixth Edition · Second Printing DECALSDecal Description Inspection for Decals with SymbolsPart No QuantityOperators Manual Ground Controls Side Chassis Platform Engine SideSixth Edition · Second Printing DECALSObserve and Obey Free-wheelConfiguration for WinchingTransport and Lifting Instructions Securing the Platform Securing to Truck or Trailer for TransitSecuring the Chassis Chassis Lifting InstructionsChassis Lifting Points LiftingMaximum slope rating, stowed position, 4WD SpecificationsMaximum slope rating, stowed position, 2WD Floor loading informationZ-60/34Range of Motion Distributed By California Proposition