English
Integrated Peripherals |
|
|
| ||||
|
|
|
| ||||
|
| CMOS Setup |
| ||||
|
|
|
| Integrated Peripherals |
|
| |
|
| [Enabled] |
| Item Help | |||
| [Enabled] |
| Menu Level` | ||||
|
|
| [Auto] |
|
|
| |
x | SATA Port0 configure as |
| SATA Port0 |
|
| ||
| SATA Port1 configure as |
| SATA Port1 |
|
| ||
| USB Controller |
|
| [Enabled] |
|
|
|
| USB 2.0 Controller |
| [Enabled] |
|
|
| |
| USB Keyboard Support |
| [Disabled] |
|
|
| |
| USB Mouse Support |
| [Disabled] |
|
|
| |
| AC97 Audio |
|
| [Auto] |
|
|
|
| Onboard H/W LAN |
| [Enabled] |
|
|
| |
| Onboard LAN Boot ROM |
| [Disabled] |
|
|
| |
| Onboard Serial Port 1 |
| [3F8/IRQ4] |
|
| ||
| Onboard Serial Port 2 |
| [2F8/IRQ3] |
|
| ||
| UART Mode Select |
| [Normal] |
|
|
| |
x | UR2 Duplex Mode |
| Half |
|
|
| |
| Onboard Parallel Port |
| [378/IRQ7] |
|
| ||
| Parallel Port Mode |
| [PRINTER] |
|
| ||
x | ECP Mode Use DMA |
| 3 |
|
|
| |
KLJI: Move | Enter: Select | F10: Save | ESC: Exit | F1: General Help | |||
| F5: Previous Values |
| F6: |
| F7: Optimized Defaults | ||
|
|
|
|
|
| ||
|
|
|
|
|
| ||
| Enabled |
| Enable onboard 1st channel IDE port. (Default value) |
| |||
| Disabled |
| Disable onboard 1st channel IDE port. |
|
| ||
|
|
|
|
| |||
| Enabled |
| Enable onboard 2nd channel IDE port. (Default value) |
| |||
| Disabled |
| Disable onboard 2nd channel IDE port. |
|
| ||
|
|
|
|
|
|
| |
| Disabled |
| Disable onboard Seria ATA function. |
|
| ||
| Auto |
| When there is no device to be plugged in IDE1 or IDE2, SATA controller will | ||||
|
|
| remap to IDE controller. (Default value) |
|
| ||
| Manual |
| Set SATA mode manually from "SATA Port0 configure as" item. | ||||
| SATA Port0 configure as |
|
|
|
| ||
| IDE Pri. Master | Set SATA controller to compatible mode. This mode will remap SATA Port 0 to | |||||
|
|
| IDE Primary Master. |
|
|
| |
| IDE Pri. Slave | Set SATA controller to compatible mode. This mode will remap SATA Port 0 to | |||||
|
|
| IDE Primary Slave. |
|
|
| |
| IDE Sec. Master | Set SATA controller to compatible mode. This mode will remap SATA Port 0 to | |||||
|
|
| IDE Secondary Master. |
|
|
| |
| IDE Sec. Slave | Set SATA controller to compatible mode. This mode will remap SATA Port 0 to | |||||
|
|
| IDE Secondary Slave. |
|
|
| |
| SATA Port0 |
| Set SATA controller to native mode(Serial ATA mode - SATA Port 0). This mode | ||||
|
|
| is only supported by Windows XP or later. (Default value) |
| |||
| SATA Port1 |
| Set SATA controller to native mode(Serial ATA mode - SATA Port 1). This mode | ||||
|
|
| is only supported by Windows XP or later. |
|
| ||
SATA Port1 configure as
The setting depends on "SATA Port0 configure as" item setting. (Default: SATA Port1)
- 34 - |
