Integrated Peripherals | Gigabyte GA-8S661FXM-775 instruction

English

2-3	Integrated Peripherals

		CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
				Integrated Peripherals
	IDE1 Conductor Cable			[Auto]		Item Help
	IDE2 Conductor Cable			[Auto]		Menu Level `
	On-Chip Primary PCI IDE			[Enabled]
	On-Chip Secondary PCI IDE			[Enabled]		[Auto]
	AC97 Audio			[Enabled]		Auto-detect IDE
	Onboard LAN device			[Enabled]		cable type
	USB Controller			[Enabled]
	USB Legacy Support			[Disabled]		[ATA 66/100/133]
	SiS Serial ATA Controller			[Enabled]		Set Conductor Cable
	SiS Serial ATA Mode			[RAID]		to ATA66/100/133 (80
	Onboard Serial Port 1			[3F8/IRQ4]		Pins)
	Onboard Serial Port 2			[2F8/IRQ3]
	Onboard Parallel Port			[378/IRQ7]		[Disabled]
	Parallel Port Mode			[ECP]		Set Conductor Cable
	ECP Mode Use DMA			3		ATA33 (40 Pins)
KLJI: Move		Enter: Select		+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults		F7: Optimized Defaults

	IDE1 Conductor Cable
	Auto		BIOS autodetects IDE1 conductor cable .(Default Value)
	ATA66/100/133		Set IDE1 Conductor Cable to ATA66/100/133 (Please make sure your
			IDE device and cable are compatible with ATA66/100/133).
	ATA33		Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	IDE2 Conductor Cable
	Auto		BIOS autodetects IDE2 conductor cable. (Default Value)
	ATA66/100/133		Set IDE2 Conductor Cable to ATA66/100/133. (Please make sure your
			IDE device and cable are compatible with ATA66/100/133)
	ATA33		Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE
			device and cable are compatible with ATA33)
	On-Chip Primary PCI IDE
	Enabled		Enable onboard 1st channel IDE port. (Default value)
	Disabled		Disable onboard 1st channel IDE port.
	On-Chip Secondary PCI IDE
	Enabled		Enable onboard 2nd channel IDE port. (Default value)
	Disabled		Disable onboard 2nd channel IDE port.
	AC97 Audio
	Enabled		Autodetect AC97 audio function. (Default value)
	Disabled		Disable AC97 audio function.

GA-8S661FXM-775 Motherboard

- 36 -

Image 36

Gigabyte GA-8S661FXM-775 user manual Integrated Peripherals

Contents

GA-8S661FXM-775 Motherboard GA-8S661FXM-775 Copyright Product Manual Classification Table of Contents Drivers Installation GA-8S661FXM-775 Motherboard Layout GA-8S661FXM-775 Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your Computer Feature Summary CPU Use of licensed Award Bios Installation of the CPU and Heatsink Installation of the CPU Installation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1/IDE2 IDE Connector FDD FDD Connector SATA0/SATA1 Serial ATA Connector, Controlled by SiS964 Faudio Front Audio Panel Connector Fpanel Front Panel Connector Surcen Cdin CD in Connector Spdifio Spdif In/ Out 13 F1USB / F2USB Front USB Connectors CI Chassis Intrusion, Case Open Comb Comb Connector Clrcmos Clear Cmos BAT Battery Pwrled English English Status Page Setup Menu / Option Page Setup Menu Main Menu Main Menu For example Bios Ver. E3 „ Set Supervisor Password „ Set User Password„ Save & Exit Setup „ Exit Without Saving Time IDE Channel 0 Master, Slave /IDE Channel 1 Master, Slave Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on Memory Hard Disk Boot Priority First / Second / Third Boot Device Boot Up Floppy Seek Password CheckCPU Hyper-Threading Limit Cpuid Max. to Integrated Peripherals SiS Serial ATA Mode Parallel Port ModeECP Mode Use DMA Onboard LAN device IRQ 3-7, 9-15, NMI ModemRingOn Power On By Keyboard Power On By MouseResume by Alarm Power LED in S1 State PnP/PCI Configurations Current CPU Temperature Case OpenedCurrent VoltageV Vcore / DDR 2.5V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPM CPU Smart FAN Mode Configure Dram TimingCAS Latency Setting Dram RAS to CAS Delay Dram RAS Active TimeDram RAS Precharge Time CPU Clock Ratio MHz Top Performance Load Optimized Defaults Set Supervisor/User Password Save & Exit Setup Exit Without Saving Bios Setup English Drivers Installation Install Chipset Drivers Software Applications Driver CD Information Hardware Information Contact Us English Xpress Recovery2 Introduction How to use the Xpress Recovery2Unique Software Utility System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Bios Flash Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utility Using the Q-FlashTMutility Steps You can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen English Congratulation!! You have updated Bios successfully Bios file becomes F4 after updating Method 2 @BIOSTM Utility Methods and steps English Serial ATA Bios Setting Utility Introduction RAID Levels Configuring the SiS RAID Bios Creating RAID Volume Udma RAID0 English Deleting RAID Volume Installing the RAID Drivers Channel Audio Setup 4 2 / 4 / 6 Channel Audio Function Introduction Channel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing Introuction Manual setting Troubleshooting AMI Bios Beep Codes English English English English English English English Contact Us Taiwan Headquarters China Shanghai