Integrated Peripherals, Init Display First | Gigabyte GA-K8NMF-9

Init Display First

This feature allows you to select the first initiation of the monitor display from which card when you install a PCI card and a PCI Express VGA card on the motherboard.

PEG	Set Init display first to PCI Express VGA card. (Default value)
PCI slot	Set Init display first to PCI.

2-3 Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Integrated Peripherals

English

On-Chip IDE Channel0	[Enabled]
On-Chip IDE Channel1	[Enabled]
IDE DMA transfer access	[Enabled]
On-Chip MAC Lan	[Auto]
On-Chip LAN BOOT ROM	[Enabled]
NV IDE/SATA RAID function	[Enabled]
x IDE Primary Master RAID	[Disabled]
x IDE Primary Slave RAID	[Disabled]
x IDE Secndry Master RAID	[Disabled]
x IDE Secndry Slave RAID	[Disabled]
NV Serial-ATA 1	[Enabled]
x NV SATA 1 class code	[0101]
x NV SATA 1 Primary RAID	[Enabled]
x NV SATA 1 Secondary RAID	[Enabled]
NV Serial-ATA 2	[Enabled]
x NV SATA 2 class code	[0101]
x NV SATA 2 Primary RAID	[Enabled]
x NV SATA 2 Secondary RAID	[Enabled]
IDE Prefetch Mode	[Enabled]

Item Help

Menu Level`

KLJI: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values		F7: Optimized Defaults

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Integrated Peripherals

USB Memory Type	[SHADOW]
AC97 Audio	[Auto]
Onboard 1394
Onboard Serial Port 1	[3F8/IRQ4]
Onboard Serial Port 2	[2F8/IRQ3]
Onboard Parallel Port	[378/IRQ7]
Parallel Port Mode	[SPP]
x ECP Mode Use DMA	3
On-Chip USB	[V1.1+V2.0]
Legacy USB Keyboard/Storage	[Disabled]
Legacy (DOS) USB Mouse	[Disabled]
Legacy USB Storage detect	[Enabled]

Item Help

Menu Level`

KLJI: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values		F7: Optimized Defaults

- 35 -

BIOS Setup

Image 35

Gigabyte GA-K8NMF-9 user manual Integrated Peripherals, Init Display First

Contents

GA-K8NMF-9 Motherboard Product Manual Classification Copyright Table of Contents Drivers Installation K8NMF-9 GA-K8NMF-9 Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-Warranty SATA2, SATA3 Feature Summary Bios Installation of the CPU Installation of the CPU and Fan Heat Sink Installation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power Connector IDE1 / IDE2 IDE Connector Fpanel Front Panel Jumper BAT Battery Cdin CD In Connector Faudio Front Audio Panel Connector Spdifio Spdif In / Out Connector Surcen Surround Center Connector 15 F11394 Front Ieee 1394 Connectors USB1 / FUSB2 Front USB Connector Clrcmos Clear Cmos CI Chassis Intrusion, Case Open English English Main Menu Status Page Setup Menu / Option Page Setup Menu F12 For Boot Menu Main Menu For example Bios Ver. F8 „ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management Setup IDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Time Halt on Floppy 3 Mode Support for Japan AreaIDE Channel 2/3/4/5 Master Drive a / Drive B Password Check Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy Seek Init Display First Integrated Peripherals On-Chip IDE Channel1 IDE DMA transfer accessOn-Chip LAN Boot ROM On-Chip IDE Channel0 NV Sata 2 class codeNote IDE Prefetch ModeNV Sata 1 Primary RAID NV Sata 1 Secondary RAID On-Chip USB Parallel Port ModeECP Mode Use DMA Onboard Parallel Port USB Resume from Suspend Power-On by AlarmPME Event Wake Up Modem Ring On AC Back Function Power On by MousePower On by Keyboard KB Power on Password Current VoltageV Vcore / DDR25V / +3.3V / +12V PC Health StatusCase Opened Current CPU/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature Temp of FAN turn off Default temperature 0oC Temp of full FAN Speed Default temperature 70oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp Limit of High Speed Default temperature 60oC Load Optimized Defaults Exit Without Saving Save & Exit Setup English Install Chipset Drivers Drivers Installation Software Information Software Application Contact Us Hardware Information English User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction How to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/N Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutility Steps Using the Q-FlashTMutility You can repeat to Part Two English Exploring the Q-FlashTMutility screen Bios file becomes F4 after updating Congratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM Utility English RAID Levels Serial ATA Bios Setting Utility Introduction Entering the RAID Bios Setup Configuring the Nvidia RAID Bios Assigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block Size Completing the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and Settings Channel Audio Setup English English English Spdif Output Device Optional Device Auto-detecting Introduction of audio connectorsJack-Sensing and UAJ Introduction UAJ Introduction Manual settingEnable UAJ function Troubleshooting Taiwan Headquarters Contact Us China Shanghai