Goodmans CPG SERIES installation manual 208-240/1/60 0140L00510 REV a, Installer/Serviceman

CPG036(48)0451D SINGLE PHASE 240V/60HZ DIRECT DRIVE

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

L1				SUPPLY VOLTAGE						L2
				208-240/1/60
C	T1		R				C			L2
	C		S		H	C
					F		CM
HEAT
PCB	EM		FC
COOL						PCB
						LI	DI	VM
			3	2	1
			TB1		TR
			FS	IGN	FS			IIC
F
4				LS
5
IIC		3		ALS	RS	GV
		6		PS
		8
9	7	10	12
			11	LPS	HPS		C
							NOTE	6	5	4
							4
R	G	W		Y1 Y2	C		PLF	3	2	1
						TB1
TO THERMOSTAT
TERMINAL BLOCK
			INSTALLER/SERVICEMAN
STATUS LIGHT			EQUIP. STATUS				CHECK
ON			NORMAL OPERATION				-
OFF			NO POWER OR
			INTERNAL CONTROL
				FAULT
1 BLINK			IGNITION FAILURE				GAS FLOW
				OR		GAS PRESSURE
			OPEN ROLLOUT				GAS VALVE
				SWITCH		FLAME SENSOR
				OR		FLAME ROLLOUT
			OPEN AUX. LIMIT				BAD SWITCH
				SWITCH		AUX. LIMIT OPEN
2 BLINKS			PRESSURE SWITCH				CHECK
				OPEN		PRESSURE SWITCH
3 BLINKS			WITHOUT INDUCER ON				CHECK
						PRESSURE SWITCH
4 BLINKS			OPEN LIMIT SWITCH			MAIN LIMIT OPEN
							BAD SWITCH
5 BLINKS			FALSE FLAME SENSED
6 BLINKS			COMPRESSOR				3 MIN. COMP.
			OUTPUT DELAY

COMPONENT LEGEND

ALS	AUXILIARY LIMIT SWITCH
COMP	COMPRESSOR
CM	CONDENSER MOTOR
C	CONTACTOR
EM	EVAPORATOR MOTOR
F	FUSE
FS	FLAME SENSOR
GND	EQUIPMENT GROUND
GV	GAS VALVE
HPS	HIGH PRESSURE SWITCH
IIC	INTEGRATED IGNITION CONTROL
IGN	IGNITOR
LS	LIMIT SWITCH
LPS	LOW PRESSURE SWITCH
PLF	FEMALE PLUG/CONNECTOR
PS	PRESSURE SWITCH
RCCF	RUN CAPACITOR FOR CONDENSER FAN
RS	ROLLOUT SWITCH
TB1	TERMINAL BLOCK (24V SIGNAL)
TR	TRANSFORMER
VM	VENT MOTOR
VMR	VENT MOTOR RELAY
BC	BLOWER CAPACITOR
NOTES

1.REPLACEMENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS ORIGINAL. (USE COPPER CONDUCTOR ONLY).

2.FOR 208 VOLT TRANSFORMER OPERATION MOVE BLACK WIRE FROM TERMINAL 3 TO TERMINAL 2 ON TRANSFORMER.

3.FOR DIFFERENT THAN FACTORY SPEED TAP. CHANGE COOLING SPEED AT COOL TERMINAL. CHANGE HEATING SPEED AT HEAT TERMINAL ON CONTROL BOARD

3 SPEED MOTOR RD - LOW SPEED BL - MED. SPEED BK - HIGH SPEED

4.ACCESSORY ECONOMIZER PLUG ADJACENT TO BLOWER HOUSING IN RETURN AIR COMPARTMENT. REMOVE MALE PLUG AND ATTACH FEMALE PLUG TO ECONOMIZER ACCESSORY.

5.USE COPPER CONDUCTORS ONLY.

USE NEC CLASS 2 WIRE.

6.PURPLE WIRE CONNECTS TO TRANSFORMER (PIN 1).

7.SPEED TAP TERMINATIONS SHOWN ON DIAGRAM ARE REPRESENTATIVE, BUT ACTUAL FACTORY SETTING MAY BE DIFFERENT BASED ON HEATING VALUE AND CAPACITY OF UNIT.

8.TO RUN DIFFERENT SPEED FOR HEATING AND COOLING, DISCONNECT GEEEN JUMPER FROM "COOL" TERMINAL AND REPLACE WITH APPROPRIATE SPEED TAP. THEN PLACE DISCONNECTED END OF JUMPER ON "UNUSED" TERMINAL LEFT OPEN BY MOVING THE SPEED TAP.

SEE UNIT RATING PLATE FOR TYPE AND SIZE OF OVERCURRENT PROTECTION.

208-240/1/60 0140L00510 REV A

FACTORY WIRING

LINE VOLTAGE

LOW VOLTAGE

OPTIONAL

HIGH VOLTAGE

FIELD WIRING

HIGH VOLTAGE

LOW VOLTAGE

WIRE CODE

BK BLACK

BL BLUE BR BROWN GR GREEN OR ORANGE PK PINK PU PURPLE RD RED WH WHITE YL YELLOW

BL/PK BLUE WITH PINK STRIP YL/PK YELLOW WITH PINK STRIP

THERMOSTAT

FIELD WIRING

NO ECONOMIZER
W	WH	W
G	GR	G
R	RD	R
Y1
Y/Y2	YL	Y
C	BL	C
TB1		STAT
WITH ECONOMIZER OPTION
W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y
Y/Y2
C	BL	C
TB1		STAT
2 STAGE COOLING
W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y1
Y/Y2	PK	Y2
C	BL	C
TB1		STAT

Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.

37