| Call Progress |
| Using these settings, users can configure ring or tone frequencies based on parameters |
|
| Tones |
| from local telecom. By default, they are set to North American standard. |
|
|
|
| Frequencies should be configured with known values to avoid uncomfortable high pitch |
|
|
|
| sounds. |
|
|
|
| Syntax: |
|
|
|
| (Frequencies are in Hz and cadence on and off are in 10ms) |
|
|
|
| ON is the period of ringing (“On time” in ‘ms’) while OFF is the period of silence. In order |
|
|
|
| to set a continuous ring, OFF should be zero. Otherwise it will ring ON ms and a pause |
|
|
|
| of OFF ms and then repeat the pattern. Up to three cadences are supported. |
|
|
|
|
|
|
|
|
|
|
|
| Disable Call |
| Default is No. If set to Yes, the call waiting will be disabled. |
|
| Waiting |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Use Quick IP |
| Dial an IP address under the same LAN/VPN segment by entering the last octet in the IP |
|
| Call Mode |
| address. |
|
|
|
| In the Advanced Settings page there is an option "Use Quick |
|
|
|
| setting is No. When set to YES, and #XXX is dialed, where X is |
|
|
|
| phone will make direct IP call to aaa.bbb.ccc.XXX where aaa.bbb.ccc comes from the |
|
|
|
| local IP address REGARDLESS of subnet mask. |
|
|
|
| #XX or #X are also valid so leading 0 is not required (but OK). See Quick IP Call Mode |
|
|
|
| for details. |
|
|
|
|
|
|
|
|
|
|
|
| Lock keypad |
| If set to “Yes”, the configuration changes via keypad are disabled. |
|
| update |
|
|
|
|
|
|
|
|
| Table 12: SIP Account Settings |
|
| ||||
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| Account Name |
|
| The name associated with each account - displayed on LCD. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| SIP Server |
|
| SIP Server’s IP address or Domain name provided by VoIP service provider. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Outbound Proxy |
|
| IP address or Domain name of Outbound Proxy, Media Gateway, or Session | ||
|
|
|
|
| Border Controller. Used for firewall or NAT penetration in different network | ||
|
|
|
|
| environment. If the system detects symmetric NAT, STUN will not work. ONLY | ||
|
|
|
|
| outbound proxy can provide solution for symmetric NAT. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| SIP User ID |
|
| User account information provided by VoIP service provider (ITSP); either an | ||
|
|
|
|
| actual phone number or formatted like one. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Authenticate ID |
|
| SIP service subscriber’s Authenticate ID used for authentication. It can be | ||
|
|
|
|
| identical to or different from SIP User ID. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Authenticate Password |
|
| SIP service subscriber’s account password for BT200 to register to (SIP) servers | ||
|
|
|
|
| of ITSP. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Name |
|
| SIP service subscriber’s name that is used for Caller ID display. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Use DNS SRV |
|
| Default is No. If set to “Yes”, the client will use DNS SRV to look up server. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Grandstream Networks, Inc. |
|
| BT200 User Manual | Page 27 of 33 | ||
|
|
|
|
| Firmware 1.1.5.15 | Last Updated: 01/2008 | |
