OPERATING

Adjusting Overall Cutting Height

NOTE: When adjusting U-bolts, maintain a minimum clearance of 3

mm(1/8 in.) between mower deck and stop pads. Adjust both sides of the mower deck equally. All lift chains must remain taut.

MX20099

1.Adjust four U-bolts (A) (two on each side of deck) until blade tip height is within 73-79 mm (2-7/8-3-1/8 in.) of the 76 mm (3 in.) setting.

Adjusting Mower Deck Anti-Scalp Wheels

NOTE: The flattest cut can be achieved by having all anti-scalp wheels adjusted off the ground. Check anti-scalp wheel adjustments each time the mower deck cutting height is changed.

It is recommended that all anti-scalp wheels be kept off the ground to minimize scuffing.

1.Inflate tires to correct pressure.

2.Adjust mower deck to desired cutting height.

MX15658

3.Adjust anti-scalp wheel (A) to one of three positions (D).

•Remove screw (E), nut (C) and washer (B).

•Adjust wheel up or down so it is approximately 6–13 mm (1/4–1/2 in.) above mowing surface.

4.Install wheel with attaching hardware.

5.Adjust all wheels to the same height.

Testing Safety Systems

c

CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.

Move the machine to an outside area before running the engine.

Do not run an engine in an enclosed area without adequate ventilation.

•Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area.

•Allow fresh outside air into the work area to clear the exhaust fumes out.

The safety systems installed on your machine should be checked before each machine use. Be sure you have read the machine operator manual and are completely familiar with the operation of the machine before performing these safety system checks.

Use the following checkout procedures to check for normal operation of machine.

cIf there is a malfunction during one of these procedures, do not operate machine. See your authorized dealer for service.

Perform these tests in a clear open area. Keep bystanders away.

Testing PTO Switch

1.Stand on operator’s platform with motion control levers in the neutral position.

2.Lock park brake.

3.Pull PTO switch up to engage.

4.Turn key switch to the start position.

Result: The engine must not crank.

Testing Park Brake Switch

1.Push PTO switch down to disengage.

2.Unlock park brake.

3.Turn key switch to the start position.

Result: The engine must not crank.

Testing Neutral Switch (Start)

1.Lock park brake.

2.Push PTO switch down to disengage.

3.Push one motion control lever forward.

4.Turn key switch to the start position.

Result: The engine must not crank.

Testing Neutral Switch (Run)

1.Lock park brake.

2.Push PTO switch down to disengage.

3.Start engine.

4.Push one motion control lever forward.

5.Repeat procedure using the other lever.

6.Repeat procedure pushing each motion control lever rearward.

Result: The engine must stop when either lever is moved from neutral position.

Operating - 11

Page 12 Page 14
Page 13
Image 13
Great Dane GSKH2352S, GSKW1948S manual Adjusting Mower Deck Anti-Scalp Wheels, Testing PTO Switch, Testing Park Brake Switch
Page 12 Page 14

GSKH2561S, GSKH2352S, GSKH1848S, GSKW2352S, GSKW1948S specifications

Great Dane has established itself as a leader in the manufacturing of high-quality trailers, and models like the GSKW1948S, GSKW2352S, GSKH1848S, GSKH2352S, and GSKH2561S showcase the company's commitment to innovation and durability. These models are designed to meet the evolving needs of the transportation industry, offering a blend of advanced technology, superior materials, and customizable features.

The GSKW1948S and GSKW2352S are known for their enhanced weight distribution and aerodynamics. Equipped with lightweight materials, these models help increase payload capacity while ensuring fuel efficiency. The aerodynamic design minimizes drag, ultimately leading to reduced fuel consumption, which is a significant cost-saving advantage for fleet operators.

In contrast, the GSKH1848S, GSKH2352S, and GSKH2561S are tailored for heavier loads while maintaining structural integrity and safety. These models utilize high-strength steel and advanced welding techniques to ensure they withstand the rigors of long-haul transportation. Additionally, these trailers have a robust suspension system that provides a smooth ride, reducing wear and tear on both the vehicle and the cargo.

All five models come equipped with state-of-the-art technology, featuring telematics systems that allow for real-time monitoring of trailer performance and location. This feature enables fleet managers to optimize routes and improve operational efficiency. Moreover, each model boasts easy access points for maintenance, aiding in reducing downtime and overall operating costs.

Great Dane trailers also prioritize safety with features like anti-lock braking systems and enhanced visibility lighting. The design not only meets but often exceeds industry standards for safety, providing peace of mind to operators who need to transport goods across long distances.

In conclusion, the GSKW1948S, GSKW2352S, GSKH1848S, GSKH2352S, and GSKH2561S models reflect Great Dane’s commitment to quality and innovation. With their combination of lightweight design, advanced technology, and safety features, these trailers offer reliable solutions for businesses seeking to optimize their logistics and transportation services. Investing in a Great Dane trailer means investing in efficiency, safety, and durability.
Top Page Image Contents