CARE AND CLEANING

Cleaning and sanitizing frequency must be followed according to state and local health department regulations.

NOTE: Each time the freezer is fully disassembled, all foodzone freezer components must be thoroughly washed and sanitized using procedures recommended by the local health department. In lieu of local health department recommendations, use a three compartment sink; one compartment to wash parts in detergent, one compartment to rinse, and one to sanitize.

Drain and Rinse

1.If the freezer is empty, proceed to Disassembly and Cleaning. If there is product in the freezer, turn the front panel switch to “CLEAN”. Most users schedule cleaning when product in the hopper is low to minimize product loss.

2.On freezers using the optional Remote Fill Control and Proportioning Pump, turn “OFF” the water valve on the Proportioning Pump, using the valve next to the inlet pressure regulator and turn the switch on the Remote Fill Control to “OFF”.

3.Open the front dispensing valve and drain all product from the freezer. Close the dispensing valve and turn freezer to “OFF”.

NOTE: Use approximately 2½ gallons (10 liters) of cool water to rinse product out of freezer.

4.Remove the carburetor tube and pour water into the storage hopper. Allow the water to fill the freezing cylinder.

5.Turn the panel switch to “CLEAN” for 5 minutes.

6.Open the dispensing valve and drain the water from the freezer.

7.Turn the freezer “OFF”.

Disassembly and Cleaning

Note: For cleaning and sanitizing before initial start-up remove carb tube, dispense plunger, handle and spring from parts bag first.

1.Disassemble the dispensing valve assembly (Figure M). Pull out valve handle retaining pin while supporting the valve plunger from the bottom (Figure N). Push up on the valve plunger and remove the stainless handle (Figure O). Slide the valve plunger and spring downward to remove (Figure P).

2.Remove knobs and carefully remove the front dispensing valve assembly, leaving the dasher assembly in the cylinder. Remove the o-rings from the plunger assembly and back of the dispensing valve body. (See Figure Q)

Figure M Disassemble

Figure N Remove Pin Figure O Remove Handle

Figure P Remove

Dispensing Valve

 

Plunger and Spring

NOTE: The best way to remove an o-ring is to first wipe off all of the lubricant using a clean paper towel. Pinch the o-ring upward with a dry paper towel between your index finger and thumb. When a loop is formed in the o-ring, roll it out of the groove with your other thumb. Always remove the o-ring farthest from the end of the plunger first.

Carefully inspect the o-rings and replace if necessary. (See Figure Q)

3.Remove the dasher assembly from inside the freezing cylinder taking care to avoid damaging the rear seal assembly at the back of the freezing cylinder. Disassemble the dasher assembly by removing the scraper blades, stator rod and front and rear stator rod bearings.

Figure Q Ring Removal

Page 8

Model 3511

 

 

Page 10
Image 10
Grindmaster 3511 manual Care and Cleaning, Drain and Rinse, Disassembly and Cleaning

3511 specifications

The Grindmaster 3511 is a state-of-the-art commercial coffee grinder that has become a staple in cafes, restaurants, and specialty coffee shops around the world. Known for its exceptional performance and reliability, the Grindmaster 3511 showcases several key features and technological advancements that cater to the demands of both baristas and coffee enthusiasts.

One of the most notable features of the Grindmaster 3511 is its precision grinding capabilities. The grinder is equipped with high-quality flat burrs that ensure a uniform grind size, which is essential for optimal extraction and the development of rich and flavorful coffee profiles. With adjustable grind settings, users can easily switch from espresso to French press grinds, accommodating various brewing methods and preferences.

The Grindmaster 3511 has a robust construction designed for heavy use in commercial settings. The grinder’s durable materials and components ensure longevity and consistent performance, allowing it to withstand the rigors of daily operation. This reliability is complemented by an efficient motor that operates quietly, making it suitable for environments where customer experience is paramount.

In terms of technology, the Grindmaster 3511 features an intuitive digital interface that simplifies the grinding process. The built-in timer allows baristas to set precise grind times, ensuring consistent doses for each brew. This precision is crucial in maintaining the quality and flavor of the coffee, which can vary significantly with inconsistent grind sizes.

Additionally, the Grindmaster 3511 is designed with user-friendly maintenance features. The removable grind chamber and easy access to critical components make cleaning and upkeep straightforward, promoting hygiene and prolonging the life of the grinder. This ease of maintenance is particularly beneficial for busy establishments where time is of the essence.

Moreover, the Grindmaster 3511 integrates safety features such as an automatic shut-off system, which helps prevent overheating and protects the motor during prolonged use. This attention to safety and efficiency ensures that the grinder not only meets but exceeds industry standards.

Overall, the Grindmaster 3511 stands out for its combination of precision, durability, and ease of use. Its advanced grinding technology and thoughtful design make it a valuable investment for any coffee business aiming to deliver high-quality beverages consistently. With the Grindmaster 3511, users can expect a reliable grinding experience that enhances the overall coffee-making process.