SECTION 5: SERVICE
Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570)
Turn OFF the machine, allow all moving parts to come to a complete stop, and disconnect the spark plug wire before moving the machine, emptying the bag, unclogging the inlets or outlets, filling the gas tank, or performing maintenance and repairs.
Troubleshooting
Symptom |
| Possible Cause | Possible Solution | ||
|
|
|
|
|
|
Engine will not start. |
| 1. | Control levers are not in correct positions for | 1. | Make sure the ON/OFF switch is ON, the fuel |
|
|
| starting. |
| |
|
|
|
|
| throttle controls are in the start position. |
|
| 2. | Spark plug wire is not connected to the spark | 2. | Connect the spark plug wire or replace the |
|
|
| plug, or the spark plug is bad. |
| spark plug. |
|
| 3. | No gas, or gas is old and stale. | 3. | If empty, fill the tank. If full, drain the gas, |
|
|
|
|
| then fill the tank with fresh gas. |
|
| 4. | Air filter is dirty. | 4. | Clean out the air filter. |
|
| 5. | Engine oil is low. | 5. | Add oil to the engine. |
|
| 6. | Blocked fuel line. | 6. | Clean out the fuel line. |
|
|
|
|
|
|
Engine does not | run | 1. | Engine is warm, and the choke is still in the | 1. | Move the choke to the RUN position. |
smoothly. |
|
| CHOKE position. |
|
|
|
| 2. | Air filter is dirty. | 2. | Clean the air filter. |
|
| 3. | Stale fuel, water or dirt in fuel, blocked fuel | 3. | Drain the fuel tank, clean out the fuel line, |
|
|
| line. |
| and fill the tank with fresh gas. |
|
|
|
|
|
|
Engine overheats. |
| 1. | Chips and sawdust around the motor. | 1. | Clean off the motor. |
|
| 2. | Dirty air filter. | 2. | Clean out the air filter. |
|
|
|
|
| |
Machine vibrates or makes | 1. | Loose or damaged parts. | 1. | Check the blades, hammers, impeller, and all | |
unusual noises. |
|
|
|
| connections. Tighten, repair, or replace any |
|
|
|
|
| loose or damaged parts. |
|
| 2. | Impeller or blades have woody residue or | 2. | Clean the impeller and blades. |
|
|
| chunks stuck to them. |
|
|
|
|
|
|
|
|
Chipper/shredder no | lon- | 1. | Dull or damaged blades and hammers. | 1. | Sharpen or replace blades and check the |
ger chips or shreds well. |
|
|
| hammers for damage. | |
|
| 2. | Loose, worn, or damaged | 2. | Replace or tighten |
|
|
|
|
| |
Chips do not come out | 1. | Discharge chute or hopper is clogged. | 1. | Turn OFF the motor, disconnect the spark | |
of the discharge chute or |
|
|
| plug, then clean out the machine. | |
come out slowly. |
| 2. | Insufficient motor RPM's. | 2. | Move the throttle to FAST. |
|
| ||||
|
|
|
|
|
|
G0594 Large Chipper/Shredder |