VI. CLEAN-UP BEFORE ASSEMBLY

All of the unpainted surfaces on this machine – and a few of the painted ones – are coated with a preservative oil, called Cosmolene, which prevents rust and corrosion during shipping. The coating can be removed with paint thinner (mineral spirits) and a good supply of paper towels, although you may find that careful scraping with a putty knife may be necessary where the coating is particularly thick. Use caution when removing the coating with your putty knife to avoid scratching the table top or painted surfaces on your shaper.

DO NOT use gasoline, lacquer thinner, acetone, or other highly-flammable solvents. The possibility of flash fire or explosion is far greater and they don’t work much better anyway. Don’t use chlorinat- ed solvents, such as perchloroethelene; they will lift the paint and ruin the shaper’s finish. Be care- ful when working around the drive belts. Any solvent that cuts grease will, in the long run, be harm- ful to rubber. While you are cleaning the shaper, please pay attention to the following rules:

1.Work only in a well-ventilated area.

2.Make sure there are no sources of open flame in your work area, such as pilot lights or wood- stoves.

3.DO NOT smoke while you’re working.

4.Dispose of soiled towels in a proper manner to avoid fire and environmental damage.

Packaged in a separate box you will find a number of parts also covered with Cosmolene. The small- er pieces are best cleaned by placing them in a container of solvent for several minutes. After soak- ing, the remaining coating may be removed with firm pressure, using rags or paper towels. Some pieces may have to be pried apart using a putty knife. Don’t forget to remove the fence assembly and clean under it. Once again, dispose of waste properly.

VII. SITE PLANNING

When placing the planer in your shop, three considerations should be addressed; floor load, work- ing clearances and electrical requirements. We’ll look at the first two requirements now and leave the third for the next section.

A. FLOOR LOAD

Your Model G1024 Shaper represents a fairly large weight load in a small footprint. For planning pur- poses, the intended work area should be able to take a uniform distributed live load of 100 pounds per square foot. Most commercial and residential floors are suitable for the Model G1024, though some older wooden residential floors may require some additional build up to support both machine and operator.

B. WORKING CLEARANCES

Working clearances will vary from one customer to the next, depending on individual requirements. Place your shaper in a position that can handle your most ambitious shaping requirements. The working area around the shaper should be lit well enough to eliminate shadows.

- 6 -

Page 7 Page 9
Page 8
Image 8
Grizzly G1024 instruction manual VI. CLEAN-UP Before Assembly, VII. Site Planning, Floor Load, Working Clearances
Page 7 Page 9

G1024 specifications

The Grizzly G1024 is a powerful and versatile table saw that has earned a reputation among woodworkers for its reliability and precision. Designed for both amateur and professional use, it combines advanced technologies with user-friendly features, ensuring that it meets the demands of various woodworking projects.

One of the standout features of the G1024 is its robust 1 HP motor. This motor delivers substantial power for cutting through various materials such as hardwood, softwood, and composite materials with ease. The saw is equipped with a 10-inch blade, which is standard in the industry and allows for a wide range of cuts, from rip cuts to crosscuts. The G1024 also supports a maximum cutting depth of 3-1/8 inches at 90 degrees and 2-1/4 inches at 45 degrees, making it versatile for different angles and thicknesses.

The G1024 incorporates a precision-ground cast-iron table, which provides stability and minimizes vibration during operation. The flat surface of the table ensures accurate cuts and is easy to maintain. The table size allows for extensive workpieces, with a generous extension table available for larger projects. In addition, the integrated T-slot miter gauge permits smooth movement of the gauge for precise angle cuts.

Safety is a priority in the design of the G1024. It comes with a blade guard that ensures protection against accidental contact with the spinning blade. The push stick and anti-kickback pawls further enhance user safety, allowing woodworkers to handle materials confidently without the fear of injury.

Another notable feature of the Grizzly G1024 is its fence system. The saw includes a reliable rip fence that locks securely in place, ensuring straight and accurate cuts every time. The fence’s easy adjustment mechanism allows for quick changes in width, making it an efficient tool for varying projects.

Overall, the Grizzly G1024 is designed to cater to woodworkers' needs, thanks to its blend of power, precision, and safety. Its advanced features make it suitable for a wide range of woodworking tasks, while its build quality ensures durability. Whether crafting furniture, cabinetry, or other wood projects, the G1024 stands as a dependable saw that enhances productivity and creativity in the workshop.
Top Page Image Contents