Safety Instructions For Power Tools

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace exten- sion cords if they become damaged.

Minimum Gauge for Extension Cords

 

 

LENGTH

 

AMP RATING

25ft

 

50ft

100ft

0-6

16

 

16

16

7-10

16

 

16

14

11-12

16

 

16

14

13-16

14

 

12

12

17-20

12

 

12

10

21-30

10

 

10

No

 

 

 

 

 

10.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safe- ty glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool.

13.DO NOT OVER-REACH.Keep proper footing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

15.USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. On machines with magnet- ic contact starting switches there is a risk of starting if the machine is bumped or jarred. Always disconnect from power source before adjusting or servicing. Make sure switch is in OFF position before reconnect- ing.

17.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

18.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. DO NOT leave tool until it comes to a complete stop.

19.NEVER OPERATE A MACHINE WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Full mental alert- ness is required at all times when running a machine.

20.NEVER ALLOW UNSUPERVISED OR UNTRAINED PERSONNEL TO OPER- ATE THE MACHINE. Make sure any instructions you give in regards to machine operation are approved, correct, safe, and clearly understood.

21.IF AT ANY TIME YOU ARE EXPERIENC- ING DIFFICULTIES performing the intend- ed operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed.

G1067Z Wood Lathe

-3-

Page 4 Page 6
Page 5
Image 5
Grizzly G1067Z instruction manual Length
Page 4 Page 6

G1067Z specifications

The Grizzly G1067Z is a versatile and powerful tool designed for woodworking enthusiasts and professionals alike. This premium table saw combines functionality, innovation, and convenience to deliver exceptional performance in various cutting tasks. Tailored for both hobbyists and serious woodworkers, the G1067Z stands out with its robust engineering and comprehensive features.

At the heart of the Grizzly G1067Z is a potent 2 HP motor, providing ample power to handle a wide range of materials including hardwood, softwood, and plywood. The motor drives a 10-inch blade, which can be adjusted for both height and angle, allowing for precise cuts in any scenario. With a maximum rip capacity of 30 inches to the right, and 12 inches to the left, users can confidently cut larger sheets of material without compromising accuracy.

One of the signature features of the G1067Z is its built-in gravity rise stand. This unique design not only offers stability during use but also allows for easy maneuverability and storage. The stand raises and lowers with minimal effort, ensuring that the table saw is always at the right height for the user, promoting ergonomics and reducing fatigue during extended projects.

Safety is a top priority with the Grizzly G1067Z. It comes equipped with an easy-to-access emergency shut-off switch, ensuring the user can quickly halt operation in case of unexpected situations. Additionally, the table saw includes a riving knife and blade guard, which help to prevent kickback and enhance user safety during cutting tasks.

Another notable characteristic of the G1067Z is its precision-engineered table surface, crafted from high-quality cast iron. This ensures maximum flatness and stability, contributing to accurate cuts. The extension wings provide additional surface area, essential for larger projects, while the integrated miter gauge and fence system offers straightforward adjustments for repeated accuracy.

In summary, the Grizzly G1067Z table saw is an outstanding choice for anyone serious about woodworking. Its powerful motor, innovative features, and commitment to safety and precision make it a cornerstone tool in any workshop. Whether you're cutting intricate joinery or tackling larger sheets of material, the G1067Z is equipped to meet the demands of any woodworking project, ensuring quality results every time.
Top Page Image Contents