Special
Searching for digital television channels from a satellite manu- ally
If you know the parameters of a new television channel, you can also search for it manually. Current transponder data can be found in the teletext, in satellite TV magazines or on the Internet.
1Open the menu with »MENU«.
2Select the line »SOURCE SETUP« with »V« or »Λ« and press »OK« to confirm.
– The »SOURCE SETUP« menu appears.
3Select »Digital Manual Tuning « with »V« or »Λ« and press »OK« to confirm.
– The menu appears.
4Select the line required for the parameters with »V« or »Λ«.
–»Frequency (MHz)«: Enter the
frequency with »1 ... 0« .
–»Symbol Rate (kS/s)«: Enter the
–»Polarization«: Use »<« or »>« to set the polarisation to »Horizontal« or »Vertical«.
–»Network Search«: use »<« or »>« to se- lect the option »On« or »Off«.
–»Scan Mode«: Use »<« or »>« to select whether you want to search for unencrypt- ed (Unencrypted) channels only, encrypt- ed (Encrypted) channels only, or for both (Unencrypted + Encrypted).
–»Service Type«: Use »<« or »>« to select whether you want to search for television channels only (TV), radio stations only
(Radio), or both (Radio + TV).
5Start the scan with »« (red).
–The »Results« menu appears, and the scan for TV channels begins.
Note:
7You can abort the search by pressing »MENU«.
6Press »MENU« to end the setting.
LNB settings
1Open the menu with »MENU«.
2Select the line »SOURCE SETUP« with »V« or »Λ« and press »OK« to confirm.
– The »SOURCE SETUP« menu appears.
3Select »Antenna Settings« with »V« or »Λ« and press »OK« to confirm.
–The »ANTENNA SETTINGS« menu ap- pears.
4Select the line required for the parameters with »V« or »Λ«.
–»Satellite«: »Press OK«, select a satellite with »<«, »>«, »V« or »Λ« and press »OK« to confirm.
–»Transponder«: »Press OK«, select a tran- sponder with »<«, »>«, »V« or »Λ« and press »OK« to confirm. Use »« (red) to add a transponder, use »« (green) to delete it, or use »« (yellow) to change transponder data.
–»LNB Power«: Set the LNB power supply (depending on the type of LNB) to »Off« »13/18 V« or »14/19 V« with »<« or »>«.
–»LNB Type«: Select a type of LNB with »<« or »>«. Use »« (green) to save the set- ting, or use »« (red) to abort.
–»22 KHz«: Depending on the LNB type, 22 kHz audio is selected. For a univer- sal LNB, this option is set to »Auto« and
cannot be changed.
–»DISEqC mode« and »LNB selection«: depending on the type of antenna used, use »<« or »>« select the option »Off«,
»DiSEqC 1.0« or »DiSEqC 1.1«.
»Off«: for a satellite system with only one antenna.
»DiSEqC 1.0«: allows up to four satel- lites to be received simultaneously. Under »LNB selection«, use »<« or »>« to select the option »1/4«, »2/4«, »3/4« or »4/4«.
»DiSEqC 1.1«: allows up to 16 satel- lites to be received simultaneously. Under »LNB selection«, use »<« or »>« to select the option »1/16« to »16/16«.
