Cleaning and Special Maintenance
Filter Assembly
Installation
For best performance and results, the filter assembly must be cleaned.
The filter efficiently removes food particles from the wash water, allowing it to be recirculated during the cycle. For this reason, it is advisable to remove the larger food particles trapped in the filter after each wash cycle by rinsing the
Cleaning the Spray Arms
It may happen that food particles become encrusted on the sprayer arms and block the hole (see "Close up view [interior]", letters
A
B
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall, and the sides along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or left to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned, adjust the feet (screwing them in or out) of the dishwasher until it is level. In any case, the appli- ance should not be inclined more than 2°. If the appliance is level, it will help ensure proper performance.
Cold Water Connection
Connect the cold water supply hose to a threaded 3/4 (gas) con- nector and make sure that it is fastened tightly in place (see fig. 1).
If the water pipes are new or have not been used for a prolonged period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance.
Drain Hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see fig .2). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water.
fig.2
Attention:
The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain.
Troubleshooting
Hot Water Connection
Electrical Connection
It may occur that the dishwasher does not function or does not function properly. Before calling for assistance, see what can be done first: have you forgotten to press one of the buttons or to perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
-the plug is pushed into the socket correctly;
-the power is on in the house;
-the door is closed properly;
-the
-the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
-the water is turned on and the hose is connected properly;
-the water supply to the house is on and has sufficient pressure;
-the water supply hose is crimped or bent;
-the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you checked whether:
- the water is turned on and the hose is connected properly;
-the water supply to the house is on and has sufficient pressure;
-the water supply hose is crimped or bent;
-the filter for the water supply hose is clogged.
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
-the lid of the salt container is closed properly;
-the rinse aid dosage is correct.
If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised ser- vice centre and provide the following information:
-the nature of the problem;
-the model type number (Mod...) and the serial number (S/N...), which are indicated on the plate located on the side of the inner part of the door.
Never call unauthorised technicians and refuse to allow parts
to be installed that are not original spare parts.
The water supply to the appliance can also be connected to the | After making sure that the voltage and frequency values for the | ||||
house's hot water line (centralised system, heating system), as | current in the home correspond to those on the rating plate | ||||
long as it does not exceed a temperature of 60°C. | (located on the stainless steel inner door of the appliance) and | ||||
In this case, the wash cycle time will be shortened by about 15 | that the electrical system is sized for the maximum voltage on | ||||
minutes and the wash efficiency slightly reduced. | the rating plate, insert the plug into an electrical socket which is | ||||
The connection must be made to the hot water line following the | earthed properly (the earthing of the appliance is a safety re- | ||||
same procedures as for the connection to the cold water line. | quirement mandated by law). |
| |||
|
|
|
| If the electrical socket to which the appliance must be connected | |
|
|
|
| is not appropriate for the plug, replace the plug rather than using | |
|
|
|
| ||
|
|
|
| adaptors or the like as they could cause overheating and burns. | |
|
|
|
| The symbol | on the product or on its packag- |
|
|
|
| ing indicates that this product may not be treated | |
|
|
|
| as household waste. Instead it shall be handed over | |
|
|
|
| to the applicable collection point for the recycling | |
|
|
|
| of electrical and electronic equipment. By ensuring | |
| fig.1 |
|
| this product is disposed of correctly, you will help | |
|
| prevent potential negative consequences for the | |||
|
|
|
| ||
|
|
|
| environment and human health, which could other- | |
|
|
|
| wise be caused by inappropriate waste handling of | |
Warning |
| ||||
| this product. |
| |||
The appliance is to be connected to the water mains |
|
| |||
| For more detailed information about recycling of this | ||||
using new |
| ||||
| product, please contact your local city office, your | ||||
not be reused. |
| ||||
| household waste disposal service or the shop where | ||||
|
|
|
| ||
|
|
|
| you purchased the product. | |
.9.
GB
.10. |
GB |
