Remote control operation
| MUTE |
|
| POWER |
|
|
|
| |
1 |
|
|
| 10 |
| PICTURE | MTS | ZOOM |
|
2 |
|
|
| 11 |
3 | MENU | SLEEP | EPG | EXIT |
4 |
|
|
| 12 |
5 |
|
|
| 13 |
6 |
| ENTER |
| |
|
|
|
| |
|
|
|
| 14 |
|
|
|
| TV/AV |
| 1 | 2 | 3 | 15 |
|
|
|
| INFO |
7 | 4 | 5 | 6 | 16 |
|
|
| CH+ | |
| 7 | 8 | 9 | 17 |
|
|
|
| CH- |
8 |
| 0 |
| 18 |
|
|
| + | 19 |
9 |
|
| 20 | |
|
| VOLUME |
| |
Note:
a)Point the remote control unit from no more than about 5m from the remote control sensor and within about 60° of the front of the TV monitor.
b)Do not press the button too quick. Press the button after the previous operation is completed.
1.MUTE: Used to toggle between normal & muted audio.
2.PICTURE: Press this button to select the picture display effect between Dynamic, soft, personal or standard.
3.MTS: Press to select the audio output language during DTV mode if there are multi languages available, during ATV mode, press this button to select audio output like mono & stereo.
4.MENU: Press this button to access the menu interface.
5.SLEEP: Use to auto power off by setting sleep timer.
6.NAVIGATION buttons: Press to select the options under OSD setting interface or alter the settings in a menu.
7.(0~9 ): Enter numeric values and to select the channel or program directly by entering its number.
8.
: Press to go to previously selected channel.
9.
on or off state( If the main power of the set is on).
11.ZOOM: Used to select the desired display mode wide or normal. .
12.EXIT: Exit the menu interface.
13.EPG: Press this button to skim over TV programs guide.
14.OK/ENTER: Confirm the selection.
15.TV/AV: Select the desired signal input mode.
16.INFO: Press this button to display current program information.
17.CH+: Press this button to increase the channel number.
18.
19.
20.VOLUME +: Press this button to increase the speaker volume.
HOW TO USE ANTENNA
Directly connect external movable antenna to RF in, may also connect roof antenna directly.
For better reception:
Adjust the direction/position of the antenna. The signal strength depends on the area of reception. If the signal is too weak, poor or no reception is possible. This is not a malfunction.
ATTENTION:
Do not rotate the antenna in counter direction after fixing, it may get loose & effect the channel reception.
TV OPERATION
GET STARTED
Be sure the TV antenna is connected to the set properly.
Plug the AC adaptor to the power source to power on the TV set.
Slide power on/off switch to on position.
Press the TV/AV button on the remote or MODE button on the main unit to select TV Mode.
Press AUTO/OK on the unit. Then select YES & press AUTO button to program the channels onto the memory.
PROGRAMING BY REMOTE:
Press the MENU button on the remote, and then select the satellite image by using the 
key. Then press down arrow button (
) to select antenna function. Change to Air or Cable by using 
button, depending upon the type of connection. Then scroll to Auto Scan and press 
button twice, TV will start auto programing function taking all the available channels into memory.
NOTE: Auto Scan function has to be done for TV to capture channels initially.
PROGRAMING FROM UNIT
Turn the TV on and press menu button, scroll to satelite image by pressing Vol + ( 
), and then press channel - ( 
) to select antenna function. Press Vol + to choose Air or cable reception. Then press CH - ( 
) to select Auto scan function and press Vol + ( 
) and choose start scan by using CH - (
) and press Vol + ( 
). The unit will start program.
SEARCH A PROGRAM
Press CH UP/DOWN button once, the channel number changes. A desired channel can be reached using these two keys.
NUMERIC button on the remote can facilitate you to select a specific channel. If the channel number exceeds 10, input first digital unit, then another digital unit;
3
