9-5. EMERGENCY OPERATION

9-5-1. When IR wireless remote controller fails or its battery is exhausted



E.O.

SW







When the remote controller cannot be used

When the batteries of the remote controller run out or the remote controller malfunctions, the emergency operation can be done using the emergency buttons.

DEFROST/STAND BY lamp (ORANGE)  Operation lamp (GREEN)

 Emergency operation switch (cooling/heating)

 Receiver

Each press of the emergency operation switch will toggle the operation mode.

Check “COOL/HEAT” with the operation monitor display. (The display will appear orange for 5 seconds after pressing the emergency operation switch.)

[Heat pump type]

Cooling Heating Stop

[Cooling Only type]

Cooling

Stop

Operation Monitor Display

 

GREEN

ORANGE

 

 

STOP

 

 

The orange lamp follows the switch operation

 

 

 

as indicated at the left for 5 sedonds, and

COOL

 

 

 

 

then it will return to the normal display.

HEAT

 

 

 

 

 

 

OFF

ON

 

 

* Details of emergency mode are as shown below.

 

 

 

 

 

 

Operation Mod

COOL

HEAT

 

Set Temperature

24°C, 75°F

24°C, 75°F

 

Fan Speed

High

High

Airflow Direction Up and Down

Horizontal

Downward

9-5-2. When wired remote controller or indoor unit microprocessor fails

1.When the wired remote control or the indoor unit microprocessor has failed, but all other components work properly, if you set the switch (SWE) on the indoor controller board ON, the indoor unit will begin Emergency Operation.

When Emergency Operation is activated, the indoor unit operates as follows:

(1) Indoor fan is running at high speed.

+Note on the IR wireless remote control: when the remote control does not function, it is possible to activate emergency operation by using the indoor unit emergency operation switch.

However, if the indoor unit microprocessor has failed, it is nesessary to proceed with points 2 and 3 below as in the case of the wired remote control.

2.When you activate Emergency Operation of the cooling or heating, you have to set the switch (SWE) on the indoor controller board and activate Emergency Operation of the outdoor unit.

For details on how to activate Emergency Operation of the outdoor unit, refer to the outdoor unit wiring diagram.

3.Before you activate Emergency Operation, check the following points:

(1)Emergency operation cannot be activated when:

the outdoor unit malfunctions. • the indoor fan malfunctions.

when it has detected the malfunction of drain pump during self-diagnosing.

(2)Emergency Operation becomes continuous only by switching the power source on/off. ON/OFF on the remote control or temperature control etc. does not function.

(3)Avoid operating for a long time when the outdoor unit begins defrosting

while Emergency Operation of the heating is activated, because it will start to blow cold air.

(4)Emergency cooling should be limited to 10 hours maximum (The indoor unit heat exchanger may freeze).

(5)After Emergency Operation has been deactivated, set the switches etc. to their original positions.

(6)Movement of the vanes does not work in Emergency operation, thereforeyou have to slowly set them manually to the appropriate position.

21

Page 21
Image 21
Mitsumi electronic PKA-A18HA4, PKA-A12HA4 Emergency Operation, When the remote controller cannot be used, Heat pump type

PKA-A18HA4, PKA-A12HA4 specifications

Mitsumi Electric Company is known for its innovations in the electronic components sector, and among its noteworthy products are the PKA-A18HA4 and PKA-A12HA4 components. Both models represent advancements in their respective categories, characterized by reliability, high performance, and cutting-edge technology.

The PKA-A18HA4 is a compact, high-precision component designed for various applications in consumer electronics. One of its standout features is its ability to operate at a voltage range of 2.7V to 5.5V, making it versatile for different devices. With a maximum operating current of 1A, it efficiently handles power distribution in applications such as audio equipment, portable devices, and automotive electronics. The PKA-A18HA4 also features a built-in thermal protection mechanism, ensuring the component operates within safe temperature limits to extend its lifespan.

Similarly, the PKA-A12HA4 is tailored for applications requiring low power consumption without compromising performance. It operates within a voltage range of 2.4V to 3.6V, making it ideal for battery-operated devices. This model not only offers an excellent balance between power efficiency and performance but also incorporates a range of built-in safety features, including over-voltage and short-circuit protection. These features enhance the reliability of devices utilizing the PKA-A12HA4 in environments where electrical fluctuations may occur.

Both models are also characterized by their compact footprint, allowing for easy integration into various electronic systems. Their designs prioritize minimal electromagnetic interference, which is crucial for maintaining signal integrity in sensitive applications. Additionally, they are manufactured using advanced semiconductor technologies that ensure high durability and robustness.

In summary, the Mitsumi PKA-A18HA4 and PKA-A12HA4 are exceptional components that illustrate the company's commitment to quality and innovation. Their unique features, including wide operating voltage ranges, safety mechanisms, and compact designs, make them suitable for a variety of applications across multiple industries. As technology continues to advance, these products embody the standards of performance and reliability that consumers expect from modern electronic components.