(2) Setting method of each function by wired remote controller
| ||
| B: Refrigerant address | |
C: Data display area | ||
D: Request code display area | ||
| ||
| ||
| ||
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
1. | Stop operation( ). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
2. | Press the | TEST |
| button () for 3 seconds so that [Maintenance mode] appears on the screen (). | |||||||||||||||
| After a while, [00] appears in the refrigerant address number display area.(at ) | ||||||||||||||||||
3. | Press the | CHECK |
| button () for 3 seconds to switch to [Maintenance monitor]. | |||||||||||||||
| Note) It is not possible to switch to [Maintenance monitor] during data request in maintenance mode | ||||||||||||||||||
| (i.e., while | ||||||||||||||||||
| |||||||||||||||||||
| (The display () now allows you to set a request code No.) | ||||||||||||||||||
4. | Press the [TEMP ( |
|
|
| and |
|
| )] buttons () to select the desired refrigerant address. | |||||||||||
| [ScreenB] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
5. | Press the [CLOCK ( |
|
|
| and |
|
| )] buttons () to set the desired request code No.(“311~318”, “321~324”) | |||||||||||
6. | Press the | FILTER | button () to perform function setting. |
If above setting operations are done correctly, "Request code number" will appear in data display area.() [Example: When the "311" of "Request code number" is set, [311] appears on the screen.()]
[Refererence]
You can check current "request code number" setting by setting the "request code number"(“310” or “320”) and pressing the FILTER button.()
[Example: When the current setting is "Setting No.2(Request code 311)", [311] appears on the screen.()]
7. To return to normal mode, press the ON/OFF button ( ).
10-2. BACK-UP HEATING FUNCTION (CN152)
Outline of functions
The
When connecting to the connector CN152 of the indoor unit, use
|
| Temperature difference |
| ||||||
|
| (Z=Set temp. - Room temp.) |
| signal output | |||||
|
|
|
|
|
|
|
|
| |
1 |
|
|
| Z 0˚C(˚F) |
|
| OFF | ||
2 |
| 0 < Z < 2.5˚C(4.5˚F) |
| Keeping condition | |||||
3 |
|
| 2.5˚C(4.5˚F) Z |
|
| ON | |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| ON | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| OFF | |
|
|
|
|
|
|
| |||
Z | 0 | 2.5˚C(4.5˚F) | |||||||
|
|
28