INSTALLATION

MOBILE HOME INSTALLATION

Once you have properly marked the position of your unit and the fl oor protection as outlined in the Residential Installation items #1 through #8, a supply of fresh air has to be supplied to your unit.

Place your unit in position and secure it to the

floor using four lag bolts 1/4" through the four holes inside the legs. It is important to maintain the structural integrity of the Mobile Home fl oor, walls and roof when installing your unit.

For Mobile Home units installed in the U.S. the unit must be grounded using a #8 ground wire with approved termination and star washer.

CAUTION: At no time use unlabelled parts, or substitute parts made for another chimney system.

Install as per chimney manufacturer's installation instructions.

IMPORTANT

DO NOT CONNECT TO OR USE IN CON- JUNCTION WITH ANY AIR DISTRIBUTION DUCTWORK UNLESS SPECIFICALLY AP- PROVED FOR SUCH INSTALLATIONS.

If desired, the air for combustion may be drawn directly from the outside of the house, as detailed below. It is not obligatory to do this, but it may help combustion in small or poorly ventilated house.

Connect a 4" (100 mm) diameter stainless steel, or other non-combustible corrosion resistant material, to the O.S.Ahook-up box. In order to do this the O.S.Ahook-up box must be connected to the base using 1/2" (12 mm) hex head bolts.

Run the pipe (up to 54" (1372 mm) long) to the outside avoiding sharp bends and joints within cavity walls. Turn the end down and fi t corrosion resistant mesh to prevent the entry of leaves and rodents. Seal the penetration of the outside wall with silicon.

WARNING: Do not obstruct free air supply to the air inlet duct located at the back of the stove.

NOTE: Listed factory built chimney con- nectors including elbows are acceptable for use in Mobile Home Installations.

In addition to standard installation instructions the following requirements are mandatory for installation in a mobile home.

1)The stove must be permanently bolted to the fl oor of the Mobile Home using the fl oor screws provided.

2)The stove must have a permanent outside air source for combustion.

3)The stove must be electrically grounded to the steel chassis of the Mobile Home.

4)A listed double-wall connector chimney system, roof thimble, spark arrestor and roof fl ashing kit suitable for use in Mobile Homes must be used.

5)If the chimney exits the Mobile Home at a locationother than through theroof, and exits at a point 7ft. (2130mm) or less above the ground level on which the Mobile Home is positioned a guard or method of enclosing the chimney shall be fi tted at the point of exit for a height up to 7ft. (2130mm).

6)The chimney shall be attached directly to the room heater and shall extend at least 3 ft. (914mm) above the part of the roof through which it passes. The top of the chimney should project at least 2ft. (610mm) above the highest elevation of any part of the Mobile Home within 10 ft. (3048mm) of the chimney.

7)The chimney system shall comply with Local Requirements.

8)Any openings in a chimney guard where required must not permit the entrance of 3/4" (19mm) diameter rod.

9)CAUTION: THE STRUCTURAL INTEG- RITY OF THE MOBILE HOME ROOF, FLOOR, WALLS AND CEILING MUST BE MAINTAINED.

10)Check any other local building code as other local codes may apply.

11)WARNING: DO NOT INSTALLINASLEEP- ING ROOM OF A MOBILE HOME.

12)Use silicone to create an effective vapour barrier at the location where the chimney or other component penetrates to the exterior of the structure.

Hampton H200 Cast Freestanding Woodstove

15

Page 14 Page 16
Page 15
Image 15
Hampton Direct H200 installation manual Mobile Home Installation
Page 14 Page 16

H200 specifications

The Hampton Direct H200 is an innovative solution for consumers seeking convenience and efficiency in their daily tasks. This versatile device stands out in the market due to its combination of smart technology and user-friendly features, making it an essential addition to any household.

One of the key features of the H200 is its sleek and modern design, which ensures that it fits seamlessly into any home environment. Its compact size allows for easy storage and portability, making it accessible for various needs, whether at home or on the go.

The H200 boasts advanced functionality powered by cutting-edge technology. One notable aspect is its intuitive control panel, which incorporates touch-screen functionality for effortless navigation. Users can easily select different modes and settings tailored to their specific requirements, enhancing usability and flexibility.

In terms of performance, the H200 utilizes energy-efficient technology that not only reduces power consumption but also promotes sustainability. This is a significant advantage for environmentally-conscious users looking to minimize their carbon footprint while still enjoying modern conveniences.

The device is equipped with multiple settings that cater to different tasks. Whether it’s cooking, cleaning, or organizing, the H200 adapts to various functions with ease. Its powerful motor ensures efficient operation, allowing users to complete tasks quickly and effectively, saving time and effort in the process.

Additionally, the Hampton Direct H200 emphasizes safety with features such as automatic shut-off and thermal protection, ensuring that users can work confidently without the fear of overheating or accidents.

The ease of maintenance and cleaning further enhances its value. With removable parts that are dishwasher-safe, the H200 offers a hassle-free experience for users, promoting a clean and hygienic environment.

In summary, the Hampton Direct H200 represents a perfect blend of style, performance, and safety. With its array of advanced features and technologies, it stands out as a reliable tool for simplifying daily tasks. Whether used for cooking, organizing, or cleaning, the H200 is designed to meet the demands of modern living, making it a valuable investment for any household looking to enhance productivity and efficiency.
Top Page Image Contents