Manuals / Hand Held Products / Computer Equipment / Scanner

Hand Held Products IT4600, IT4X80, IT4800, IT4710 2D PQA Reporting, Full Report, Screening Report

Models: IT4X80 IT4710 IT4410 IT4800 IT4600

1 32

Download 32 pages 53.32 Kb

Page 7

2D PQA Reporting

2D PQA Reporting

Full Report

HHP's 2D PQA reporting can be enabled in two different modes: Full Report or Screening.

If you are using Quick*View, you can enable Full Report, a listing of all of a sym- bol's identifying information, measurements, and corresponding grades, by typ- ing the following menu command:

2D_PQA1

or by scanning the following bar code:

Full Report

Note: With the IT4600/4800/4X80, the PQA report is sent out as a second data/ beep sequence after the bar code data. The report has its own HHP code ID of >(0X3E) so it can be uniquely identified.

Screening Report

Screening is a grade-based mode that allows display of a limited list of identify- ing information, as well as only those measurements that are below Minimum Acceptable Grade (MAG) level. With the IT4600/4800/4X80, if all of the param- eters are met in the screening mode, only the bar code data will be output with a beep. If one or more of the measured parameters fail to meet the MAG, the PQA message is also sent with a beep.

Note: With the IT4410/4710, screening mode outputs are also accompanied by a single beep if all parameters are okay or a triple beep if one or more of the measured parameters fail to meet the MAG.

If you are using Quick*View, you can enable Screening by typing the following menu commands:

2D_PQA2	when A is the Minimum Acceptable Grade
2D_PQA3	when B is the Minimum Acceptable Grade
2D_PQA4	when C is the Minimum Acceptable Grade
2D_PQA5	when D is the Minimum Acceptable Grade

1 - 3

Image 7

Hand Held Products IT4600, IT4X80, IT4800, IT4710, IT4410 manual 2D PQA Reporting, Full Report, Screening Report

Contents

Quick Check 2D Print Quality Assessment User’s Guide Disclaimer Table of Contents Chapter 1 - Introduction X-dimension Chapter 2 - Quick*ViewChapter 3 - Customer Support Symbology User Operation IntroductionReading Techniques Symbology/Parameter Specifics Full Report 2D PQA ReportingScreening Report PDF417 11 rows x 3 cols, 25 data & 8 chks ECL = 2 X roughly = Identifying Symbol ContentThis is a representative PDF417 symbol PQA from HHP A Data Safety Margin = 100% 0 Erasures & 0 Errors PDF417 2D Stacked / Multi-rowExcessive Print Shrinkage -43% of where In Screening modes, this parameter is reported as Useful Row Height is Too Short 1.5X when that is the case 1 is the Encoded Message MicroPDF417 Aztec Code 2D Matrix 3 DATA MATRIX ECC200 24 x 24 modules in size Data Matrix1 This is a representative Data Matrix symbol 2 PQA from HHP 6 A Fixed Patterns 0 module errors 7 A Data Safety Margin = 100% QR Code1 This is a representative QR Code symbol 2 PQA from HHP 4 lists this symbols Mask Pattern and Error Correction Level MaxiCode Postnet and Planet Code Postal Height-Modulated Bar Code Symbologies 7 A Ok Bar Widths = 0.022 in 8 A Ok Inter-Bar Gaps = 0.023 in 4 Bar Sequence ADHTATDAHDDAADADAADTHTADHHDATHTADH 4-State Codes1 B15AJ6T 2 PQA from HHP 3 4-STATEBritish 34 Bars, nominally from 38.5 to 42.3 mm. in Width Table 1 Dimensional Tolerances for the Various 4-State Bar Parameter InterpretationAverage Bar/Gap Width Average Bar Height/Extension Height Codeword Yield Data Safety MarginBar Sequence Codeword Data and Check Encoded Message Error Correction/Error Correction CharactersError Correction Level ECL Error Detection/Error Detection Characters Row Height Module ErrorsSymbology Print Growth Horizontal and Vertical X-dimension Quick*View Demonstration Software Instructions Installing Quick*View from the WebSetting Up the Imager and the Quick*View Software Quick*View IT4600/4800/4X80 Temporary Quick*View ConfigurationIT4410/4710 If Communication Cannot Be Established Using the Quick*View Software Scan Data Window Latin America Obtaining Factory ServiceCustomer Support North America North America/Canada Technical AssistanceAsia Page QC2DPQA-UG Rev B