Harman-Kardon 347 owner manual Advanced Features, Turn On Volume Level, Semi-OSD Settings

Advanced Features

If you wish to make adjustments to other items on the SYSTEM SETUP menu, press the ⁄/¤ Navigation Button D to place the blue cursor bar on the desired item and press the Set Button F to make an adjustment to another menu. If you have completed all adjust- ments, press the OSD Button L to exit the menu system.

Turn On Volume Level

As is the case with most audio/video receivers, when the AVR is turned on, it will always return to the volume setting in effect when the unit was turned off. However, you may prefer to always have the AVR turn on at a specific set- ting, regardless of what was last in use when the unit was turned off. To change the default condition so that the same volume level is always used at turn-on, you will need to make an adjustment in the SYSTEM SETUP menu. To start the adjustment, press the OSD button L to bring the main menu (Figure 1) to the screen. Press the ⁄ button D, until the System -tab is highlighted in white. Press the Set button F to enter the SYSTEM SETUP menu (Figure 32).

At the SYSTEM SETUP menu make certain that the blue cursor bar is on the Volume Default line by pressing the ⁄/¤ buttons

Das needed. Next, press the Set Button

F, followed by the ‹ / › buttons E so that the word ON is shown in the video display and press Set F to confirm. Next, press the

¤button D once so that the blue cursor bar highlights the Default Volume Set line. To set the desired turn-on volume, press the Set Button F, followed by the ‹ / › buttons E or hold them pressed until the desired volume level is shown on the Default Volume Set line and press the Set Button F to confirm. Note that this setting may NOT be made with the regular volume controls.

NOTE: Since the setting for the turn-on volume cannot be heard while the setting is being made, you may wish to determine the setting before making the adjustment. To do this, listen to any source and adjust the volume to the desired

level using the regular volume controls . When the desired volume level to be used at turn-on is reached, make a note of the setting as it appears in the lower third of the video screen or in the Main Information Display Ò.

A typical volume level will appear as a negative number such as -25dB. When making the

adjustment, use the ‹/› buttons E	to
enter this setting.

Unlike some of the other adjustments in this menu, the turn-on volume default will remain in effect even when the unit is turned off completely, unless it is changed or turned off in this menu.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons D until the on- screen blue cursor bar is highlighting the desired setting. If you have no other adjustments to make, press the OSD Button L to exit the menu system.

Semi-OSD Settings

The semi-OSD system places two-line messages at the lower third of the video display screen whenever the Volume, Input Source, Surround mode or tuner frequency of any of the configura- tion settings are changed. The semi-OSD system is helpful in that enables you to have feedback on any control changes or remote commands using the video display when it is difficult to view the front-panel displays. However, you may occasionally prefer to turn these displays off for a particular listening session. You may also want to adjust the length of time the displays remain on the screen. Both of those options are possible with the AVR.

To turn off the semi-OSD system, you will need to make an adjustment in the SYSTEM SETUP menu (Figure 32). To start the adjust- ment, press the OSD button L to bring the main menu to the screen. Press the ⁄ Button D, until the System -tab is highlighted in white. Press the Set Button F to enter the

SYSTEM SETUP menu.

At the SYSTEM SETUP menu make certain that the blue cursor bar is highlighting the Semi OSD Timeout line by pressing the ⁄/¤ buttons D as needed. Next, press the Set Button F, followed by the › button

so that the word OFF is shown in the video display and press Set F to confirm the new setting.

Note that this setting is temporary and will remain active only until it is changed or until the AVR is turned off. Once the unit is turned off, the semi-OSD displays will remain activated, even if they were switched off for the previous listening session.

To change the length of time that the semi-OSD displays remain on the screen, go to the Semi OSD Timeout -line as outlined earlier, and press the Set Button F. Next, press the ‹/› Buttons E until the desired time in seconds is displayed and press the Set Button

Fto confirm the new setting. Note that unlike most of the other options in this menu, this is a permanent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons D until the blue cursor bar is highlighting the desired setting. If you have no other adjustments to make, press the OSD Button L to exit the menu system.

Full-OSD Time Out Adjustment

The FULL OSD menu system is used to simplify the setup and adjustment of the AVR using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of inac- tivity before they disappear from the screen or Time Out. This Time Out is a safety measure to prevent the menu text from burning into the CRTs in your monitor or projector, which might happen if they were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the Time Out display.

To change the Full-OSD Time Out, you will need to make an adjustment in the SYSTEM SETUP menu (Figure 32). To start the adjust- ment, press the OSD button L to bring the main menu to the screen. Press the ⁄ button D, until the System - tab on the left is highlighted in white. Press the Set Button F to enter the SYSTEM SETUP menu.

At the SYSTEM SETUP menu make certain that the blue cursor bar is highlighting the Full OSD Timeout line by pressing the ⁄/¤ Buttons D as needed. Next, press the Set Button F, followed by the ‹ / › buttons

Euntil the desired time is displayed in seconds and press the Set Button F to con- firm the new setting. Note that unlike most of the other options in this menu, this is a perma- nent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons D until the blue cursor bar is highlighting the desired set- ting. If you have no other adjustments to make, press the OSD Button L to exit the menu sys- tem.

50ADVANCED FEATURES