Programming the Remote
Example: One blink, followed by a one-second pause, followed by six blinks, followed by a one- second pause, followed by four blinks indicates that the code has been set to 164.
For future reference enter the Setup Codes for the equipment in your system here:
DVD ____________ CD ________________
VID1/VCR ________ VID3/TV __________
VID2/CBL/SAT ______________________
TAPE ______________________________
VID4 ______________________________
Learning Codes from a Remote
In addition to using codes from the remote’s internal code library, the AVR 347’s remote is able to “learn” codes from remotes that may not be in the code library. In addition, you may use this function to “learn over” the codes from a preprogrammed device to add functions not included in the preprogrammed codes. To learn or transfer codes from an IR remote to the
AVR 347’s remote, follow these steps:
1.Place the front of the original remote with the code being sent so that it is facing the IR Transmitter Window 1 on the AVR 347 remote “head-to-head.” The remotes should be between 2 and 4cm apart.
2.Select the button on the remote that you wish to use as the device selector for the codes about to be entered. This must be any of the Input Selectors 4 or the AVR Selector 5. Note that when new codes are learned with the AVR 5 Selector, they may no longer control the AVR 347.
3.Press the Input Selector 45 button
chosen and the Learn Button at the same time. Hold these buttons until the Program/SPL Indicator 2 flashes amber and the light under the device selector button turns red. Release the buttons. It is important that you begin the next step within 20 seconds.
4.Press the button on the AVR 347 remote that you wish to program. Note that the Program/ SPL Indicator 2 will stop flashing.
Important Note: Codes cannot be taught to all buttons on the remote. The buttons with the following numbers are not learnable (for numbers, see drawing on page 11): 4, 7,
8, B, I, O, Q, , , , ,
. In these cases the Program/SPL Indicator 2 keeps flashing after the button was released.
5.As long as the Program/SPL Indicator 2 is on steadily (for five seconds), press and hold the button on the original remote that you wish to “teach” into the AVR 347 remote. If you pressed the button too late or no command was received within five seconds, the Program/SPL Indicator 2 will flash red three times and then amber, then simply repeat step four. When the Program/SPL Indicator 2 turns green, release the button on the original remote. Note that the Program Indicator will then begin to flash amber again.
NOTE: If the Program/SPL Indicator 2 turns red steadily during Step 5, the program- ming was not successful. Repeat the steps to see if the code will “take.” If the indicator keeps flashing red in step 5, this code cannot be taught.
6.Repeat steps 4 though 5 for each button on the source remote that you wish to transfer to the AVR 347 remote.
7.Once all codes have been transferred from the original source remote to the AVR 347 remote,
press the Learn button . This will turn off all LEDs and turn off the learning mode.
8.Repeat Steps 1 through 7 for any additional remotes you wish to “teach” into the AVR 347 Remote.
Erasing Learned Codes
The AVR 347’s remote allows you to remove or erase the code learned into a single button for a single device, to remove or erase all the codes that have been learned for a single device, or to erase all commands that have been learned to all devices.
To erase a single learned code from within a single device’s settings, follow these steps:
1.Press and hold both the Input Selector
45within which the individual button to be erased has been programmed and the Learn
button .
2.When the red LED under the Input Selector turns red and the Program/SPL Indicator 2 flashes amber, release the buttons.
3.Press and release the Input Selector 45 again for the device within which the individual button to be erased has been programmed.
4.Press the 7 button H three times.
5.Press and release the individual button for which the code is to be erased. The Program/SPL Indicator 2 will blink green two times and then return to amber.
6.To erase other buttons within the same device, press them as noted in Step 5.
7.When all buttons to be erased have been
pressed, press the Learn button | to complete |
the process. | |
To erase all codes within a single device, follow these steps:
1.Press and hold both the Input Selector
45for which you wish to erase the codes
2.When the red LED under the Input Selector turns red and the Program/SPL Indicator 2 flashes amber, release the buttons.
3.Press and release the same Input Selector
45again for the device whose codes you wish to erase.
4.Press the 8 button H three times.
5.The Program/SPL Indicator 2 will turn off, the red light under the Input Selector will flash on and off once and the Program/SPL Indicator 2 will flash green three times to indicate that the codes have been erased.
To erase all codes that have been pro- grammed to all devices in the remote, follow these steps:
1. Press any Input Selector 45 and also
2.When the red LED under the Input Selector turns red and the Program/SPL Indicator 2 flashes amber, release the buttons.
3.Press and release the same Input Selector
45again.
4.Press the 9 button H three times.
5.The Program/SPL Indicator 2 will turn off, the red light under the Input Selector will flash on and off once and the Program/SPL Indicator 2 will flash green three times after some seconds to indicate that the codes have been erased.
