Programming the Remote
Transport Control Punch-Through
The AVR’s remote may be programmed to operate so that the Transport Control Functions P (Play, Stop, Fast Forward, Rewind, Pause and Record) for a VCR, DVD or CD will operate in con- junction with one of the other devices controlled by the remote. For example, while using and con- trolling the TV, you may wish to start or stop your VCR or DVD without having to change the device selected by the AVR or the remote. To program the remote for Transport Control
1.Press the Input Selector 4for the device you wish to have the channel control associated
with and the Mute button at the same time until the red light illuminates, under the Input Selector 4and the Program/SPL Indicator
2flashes amber.
2.Press the Play button P. The Program/SPL Indicator 2will stop flashing and stay amber.
3.Press and release the AVR 5or Input Selector button 4for the device that will be used to change the channels. The Program/SPL Indicator 2will blink green three times and then go out to confirm the data entry.
Example: To control the transport of a CD player while the remote is set to control the TV, press the VID 2/TV Input Selector button 4and the
Mute button at the same time. Next, release them and press the Play button P, followed by the CD Input Selector button 4.
NOTE: To remove the Channel Control Punch- Through and return the remote to its original con- figuration, repeat the steps shown in the example above. However, press the same Input Selector in Steps 1 and 3.
NOTE: Before programming the remote for Volume, Channel or Transport
Reassigning Device-Control Selectors
Although any of the Input Selectors 4is nor- mally assigned to the category of product shown on the remote, it is possible to reassign one of these buttons to operate a second device of another type. For example, if you have two VCRs but no tape, you may program the TAPE 4but- ton to operate a second VCR. Before you can start you must find out the
1. Press the Input Selector 4you wish to
reassign and the Mute button at the same time until the red light illuminates under the Input Selector 4and the Program/SPL Indicator
2flashes amber.
2.Press the Input Selector 4for the device, whose function you wish to program into the reas- signed button.
3.Enter the
4.Press the same Input Selector 4pressed in Step 1 once again to store the selection. The red LED under the
Example: To use the TAPE 4button to oper- ate a second VCR, first press the TAPE Input
Selector 4and the Mute button at the same time until the red light glows under the TAPE 4button. Press the VCR 4button, fol- lowed by the
4button again.
Important Note: Only those Input Selector buttons 4can be reassigned that replace other buttons for devices of the same kind. So the bottons for DVD, CD, TAPE and VCR (devices with transport functions) can replace one another as the Selectors for TV, CBL/SAT, and
VID 4.
To remove the Reassign function and return the remote to its original configuration, repeat steps 1, 3 and 4 above (not 2), however, press the same Input Selector button 4in steps 1 and 4 (i.e.
original code).
Resetting the Remote Memory
As you add components to your
1.Press any of the Input Selector buttons 4 and the ”O“ button Hat the same time until the Program/SPL Indicator 2begins to flash amber.
2.Press the ”3“ button Hthree times.
3.The red LED under the Input Selector 4will go out and the Program/SPL Indicator 2will stop flashing and turn green.
4.The Program/SPL Indicator 2will remain green until the remote is reset. Note that this may take a while, depending on how many commands are in the memory and need to be erased.
5.When the Program/SPL Indicator 2goes out, the remote has been reset to the factory settings.
PROGRAMMING THE REMOTE 43