Harman-Kardon AVR 110 Macro Programming, Press the AVR Selector f, Erasing Macro Commands

Programming the Remote

Macro Programming

Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the AVR 110’s remote con- trol. Once programmed, a macro will send out up to 19 different remote codes in a predeter- mined sequential order enabling you to auto- mate the process of turning on your system, changing devices, or other common tasks. The AVR 110’s remote can store up to five separate macro command sequences: one that is associated with the Power On button a, and four more that are accessed by pressing the Macro buttons v.

1.Press the Mute button 35 and the Macro button v to be programmed or the Power On button a at the same time. Note that an Input Selector e will light red, and the Program Indicator c will flash amber.

2.Enter the steps for the macro sequence by pressing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step. The Program Indicator c will flash green to confirm each button press as you enter commands.

NOTE: While entering commands for Power On/Off of any device during a macro sequence, press the Mute button 35 . DO NOT press the actual Power button.

3.When all the steps have been entered, press the Sleep button i to enter the commands. The red light under the Input Selectors ef will blink and then turn off.

Example: To program the Macro 1 button so that it turns on the AVR 110, TV and a Cable Box, follow these steps:

•Press the Macro 1 vand Mute 35 buttons at the same time and then release them.

•Note that the Program Indicator c will flash amber.

•Press the AVR Selector f.

•Press the Mute button 35 to store the AVR 110’s power on command.

•Press the VID 2 Input Selector button eto indicate the next command is for “TV Power On.”

•Press the Mute button 35 to store the TV Power On Command.

•Press the VID 3 Input Selector button eto indicate the next command is for “Cable Power On.”

•Press the Mute button 35 to store the Cable Power On command.

•Press the Sleep/Channel Up button i to complete the process and store the macro sequence.

After following these steps, each time you press the Macro 1 button v, the remote will send the Power On/Off command.

Erasing Macro Commands

To remove the commands that have been pro- grammed into one of the Macro buttons, follow these steps:

1.Press the Mute button 35 and the Macro button v that contains the com- mands you wish to erase.

2.Note that the Program Indicator c will flash amber, and the LED under the AVR Selector f will turn red.

3.Within ten seconds, press the Surround

Mode Selector/Channel Down button j.

4.The red LED under the AVR Selector f will go out, and the Program Indicator c will turn green and flash three times before it goes out.

5.When the Program Indicator c goes out, the Macro has been erased.

Programmed Device Functions

Once the AVR 110’s remote has been pro- grammed for the codes of other devices, press the appropriate Input Selector eto change the remote from controlling the AVR 110 to con- trolling the additional product. When you press any one of the selectors, it will briefly flash in red to indicate that you have changed the device being controlled.

When operating a device other than the AVR 110, the controls may not correspond exactly to the function printed on the remote

or button. Some commands, such as the volume control, are the same as they are with the AVR 110. Other buttons will change their function so that they correspond to a secondary label on the remote. For example, the Sleep and Surround mode selector buttons also func- tion as the Channel Up and Channel Down

1		2	3
4	5	6	7
8	9	10	11
	12
13	14	15	16
17	18	19	20
21			22
	23
24	25	26
	27
28			29
30	31	32	33
34	35	36	37
38	39	40	41
42	43	44	45
46		47	48
49	50	51	52
53	54	55

5657 58

59 60

110

28PROGRAMMING THE REMOTE