buttons when operating most TV sets, VCRs or cable boxes. The Channel Up/Down indication is printed directly on the remote. For many stan- dard CD players, cassette decks, VCRs and DVD functions, the standard function icons are printed on top of the buttons.
For some products, however, the function of a particular button does not follow the command printed on the remote. In order to see which function a button controls, consult the Function List tables printed on pages 31 and 32. To use those tables, first check the type of device being controlled (e.g., TV, VCR). Next, look at the remote control diagram pictured at the left. Note that each button has a number on it.
To find out what function a particular button has for a specific device, find the button num- ber on the Function List and then look in the column for the device you are controlling. For example, button number 50 is the Macro 2 button for the AVR 110, but it is the “Favorite” button for many cable television boxes and satellite receivers. Button number 29 is the Delay button for the AVR 110, but the + Time button for CD players.
Note that the numbers used to describe the button functions at the left for the purposes of describing how a button operates are a differ- ent set of numbers than those used in the rest of this manual to describe the button functions for the AVR 110.
Notes on Using the AVR 110 Remote With Other Devices.
•Manufacturers may use different code sets for the same product category. For that reason, it is important that you check to see if the code set you have entered operates as many con- trols as possible. If it appears that only a few functions operate, check to see if another code set will work with more buttons.
•When a button is pressed on the AVR 110 remote, the red light under the Input Selector e for the product being operat- ed should flash briefly. If the Device Control Selector flashes for some but not all buttons for a particular product, it does NOT indicate a problem with the remote but rather that no function is programmed for the button being pushed.
Volume Punch-Through
The AVR 110’s remote may be programmed to operate the Volume Control 33 and Mute
35functions of either the TV or the AVR 110 in conjunction with any of the devices con- trolled by the remote. For example, since the AVR 110 will likely be used as the sound sys- tem for TV viewing, you may wish to have the AVR 110’s volume activated, although the remote is set to run the TV. Either the AVR 110 or TV volume control may be associated with any of the remote’s devices. To program the remote for Volume Punch-Through, follow these steps:
1.Press the Input Selector efor the unit you wish to have associated with the volume control and the Mute button 35 at the same time until the red light appears under the Input Selector e and note that the Program Indicator cwill flash amber.
2.Press the Volume Up button 33 and note that the Program Indicator cwill stop flashing and stay amber.
3.Press either the AVR Selector for the Input Selector e, depending on which system’s volume control you wish to have attached for the punch-through mode. The Program Indicator cwill blink green three times and then go out to confirm the data entry.
Example: To have the AVR 110’s volume control activated even though the remote is set to control the TV, first press the Video/TV Input Selector eand the Mute button 35 at the same time. Next, press the Volume Up button 33 , followed by the AVR Selector f.
NOTE: Should you wish to return the remote to the original configuration after entering a Volume Punch-Through, you will need to repeat the steps shown above. However, press the same Input Selector in Steps 1 and 3.
Channel Control Punch-Through
The AVR 110’s remote may be programmed to operate so that the channel control function for either the TV, cable or satellite receiver used in your system may be used in conjunction with one of the other devices controlled by the remote. For example, while using and controlling
the VCR, you may wish to change channels on a cable box or satellite receiver without having to change the device selected by the AVR 110 or the remote. To program the remote for Channel Control Punch-Through, follow these steps:
1.Press the Input Selector button efor the device you wish to have the channel control associated with and the Mute button 35 at the same time until the red light appears under the Input Selector eand the Program Indicator cflashes amber.
2.Press the Volume Down button 33 . The Program Indicator cwill stop flashing and stay amber.
3.Press and release the Input Selector button efor the device that will be used to change the channels. The Program Indicator c will blink green three times and then go out to confirm the data entry.
Example: To control the channels using your Cable Box or Satellite Receiver while the remote is set to control the VCR, first press the VID 1/VCR Input Selector button e and the Mute button 35 at the same time. Next, release them and press the Volume Down button 33 , followed by the VID 2/TV Input Selector button e.
NOTE: To remove the Channel Control Punch- Through and return the remote to its original configuration, repeat the steps shown in the example above. However, press the VID 1/VCR Input Selector in Steps 1 and 3.
Transport Control Punch-Through
The AVR 110’s remote may be programmed to operate so that the Transport Control func- tions w(Play, Stop, Fast Forward, Rewind, Pause and Record) for a VCR, DVD or CD will operate in conjunction with one of the other devices controlled by the remote. For example, while using and controlling the TV, you may wish to start or stop your VCR or DVD without having to change the device selected by the AVR 110 or the remote. To program the remote for Transport Control Punch-Through, follow these steps:
1.Press the Input Selector efor the device you wish to have the channel control associ- ated with and the Mute button 35 at the same time until the red light appears, under the Input Selector eand the Program Indicator cflashes amber.
