System Configuration

OFF: When OFF is highlighted, the Night mode will not function.

MID: When MID is highlighted, a mild com- pression will be applied.

MAX: When MAX is highlighted, a more severe compression algorithm will be applied.

We recommend that you select the MID set- ting as a starting point and change to the MAX setting later, if desired.

Note that the Night mode may be adjusted directly any time that a Dolby Digital source is playing by pressing the Night button l. When the button is pressed, the phrase D-RANGE will appear in the lower third of the video screen and in the Main Information Display Y. Press the /¤ button n within three seconds to select the desired setting.

When all settings for the surround setup have been made, press the /¤ buttons n so that the cursor is next to RETURN TO MENU, and press the Set button p to return to the main menu.

Speaker Setup

This menu tells the AVR 510 which type of speakers are in use. This is important as it adjusts the settings that determine which speakers receive low-frequency (bass) informa- tion. For each of these settings use the LARGE setting if the speakers for a particular position are traditional full-range loudspeakers that are capable of reproducing sounds below 100Hz. Use the SMALL set- ting for smaller, frequency-limited satellite speakers that do not reproduce sounds below 100Hz. Note that when “small” speakers are used, a subwoofer is required to reproduce low-frequency sounds. Remember that the “large” and “small” descriptions do not refer to the actual physical size of the speakers, but to their ability to reproduce low-frequency sounds. If you are in doubt as to which catego- ry describes your speakers, consult the specifi- cations in the speakers’ owner’s manual, or ask your dealer.

It is easiest to enter the proper settings for the speaker setup through the SPEAKER SETUP menu (Figure 5). If that menu is not already on your screen from the prior adjust- ments, press the OSD button v to bring up the MASTER MENU (Figure 1), and then press the ¤ button n twice so that the cursor is on the SPEAKER SETUP line.

At this point, press the Set button p to bring up the SPEAKER SETUP menu (Figure 5).

* S P E A K E R

S E T U P *

 

 

 

 

L E F T / R I G H T :

S M A L L

 

 

 

 

 

C E N T E R

:

S M A L L

 

 

 

 

 

S U R R O U N D

:

S M A L L

 

 

 

 

S U B W O O F E R

:

S U B

 

S U B X - O V E R F R E Q : 8 0 H Z

R E T U R N T O

M E N U

 

 

 

 

 

Figure 5

When the SPEAKER SETUP menu first appears, the on-screen cursor will be at the top of the list of speaker positions, pointing toward the LEFT/RIGHT line, which sets the configuration for the front left and right speakers. If you wish to make a change to the front speakers’ configuration, press the /but-

tons o 31 so that either LARGE or SMALL appears, matching the appropriate description from the definitions shown above.

When SMALL is selected, low-frequency sounds will be sent only to the subwoofer out- put. If you choose this option and there is no subwoofer connected, you will not hear any low frequency sounds from the front channels.

When LARGE is selected, a full-range output will be sent to the front left and front right outputs. Depending on the choice made in the SUBWOOFER line in this menu, bass information may also be directed to the front left/right speakers, a subwoofer or both.

When you have completed your selection for the front channel, press the ¤ button n on the remote to move the cursor to CENTER.

Press the /buttons o 31 on the remote to select the option that best describes your system, based on the speaker definitions shown below.

When SMALL is selected, low-frequency center-channel sounds will be sent only to the subwoofer output. If you choose this option and there is no subwoofer connected, you will not hear low-frequency sounds from the center- channel speaker.

When LARGE is selected, a full-range output will be sent to the center speaker output, and NO center channel signal will be sent to the subwoofer output.

NOTE: If you choose Logic 7 as the surround mode for the particular input source for which you are configuring your speakers, the AVR 510 will not make the LARGE option available for the center speaker. This is due to the require- ments of Logic 7 processing, and does not indi- cate a problem with your receiver.

When NONE is selected, no signals will be sent to the center-channel output. The receiver will operate in a “phantom” center channel mode and center-channel information will

be sent to the left and right front channel outputs. When only front left and right speak- ers are used, with no center or surround speak- ers, VMAx is a good alternative mode.

When you have completed your selection for the center channel, press the ¤ button n on the remote to move the cursor to

SURROUND.

Press the /buttons o 31 on the remote to select the option that best describes the sur- round speakers in your system based on the speaker definitions shown on this page.

When SMALL is selected, low-frequency surround channel sounds will be sent to the subwoofer output only. If you choose this option and there is no subwoofer connected, you will not hear any low frequency sounds from the surround speakers.

When LARGE is selected, a full-range output will be sent to the surround channel outputs, and NO surround channel signals will be sent to the subwoofer output.

When NONE is selected, surround-sound information will be split between the front left and front right outputs. For optimal perform- ance when no surround speakers are in use, the Dolby 3 Stereo mode should be used.

When you have completed your selection for the surround channel, press the ¤ button n on the remote to move the cursor to SUBWOOFER.

Press the /buttons o 31 on the remote to select the option that best describes your system.

The choices available for the subwoofer posi- tion will depend on the settings for the other speakers, particularly the front left/right positions.

22SYSTEM CONFIGURATION

Page 22
Image 22
Harman-Kardon AVR 510 owner manual Speaker Setup, Surround

AVR 510 specifications

The Harman-Kardon AVR 510 is a high-performance AV receiver that has garnered attention for its impressive sound quality and versatile functionality. As part of Harman Kardon's esteemed line of audio equipment, the AVR 510 is designed to elevate the home entertainment experience, making it a favored choice for audiophiles and casual listeners alike.

One of the standout features of the AVR 510 is its powerful amplification system. With a robust output of up to 75 watts per channel, the receiver can drive a variety of speaker configurations, ensuring clear and dynamic sound across the frequency spectrum. This capability allows users to enjoy an immersive audio experience whether they are watching movies, playing video games, or listening to music.

The AVR 510 also supports multiple surround sound formats, including Dolby Digital and DTS. This enables users to experience rich, cinematic soundscapes that enhance the overall viewing experience. The inclusion of advanced processing technologies ensures that audio playback is accurate, highlighting the nuances in sound that make movies and music come alive.

Connectivity is another key aspect of the AVR 510, featuring a range of input options to accommodate various devices. With several HDMI inputs, digital optical and coaxial inputs, as well as analog audio connections, this receiver can seamlessly integrate with Blu-ray players, gaming consoles, and streaming devices. It also includes an AM/FM tuner, allowing users to enjoy their favorite radio stations.

The user interface of the AVR 510 is designed for convenience, featuring an intuitive on-screen menu that guides users through setup and operation. The inclusion of a remote control further enhances usability, allowing for easy access to settings and adjustments from across the room.

Additionally, the AVR 510 is equipped with Harman Kardon's proprietary technologies, such as Halosonic processing, which optimizes sound quality for various listening environments. This ensures that users can enjoy consistent audio performance regardless of their room's acoustics.

In conclusion, the Harman-Kardon AVR 510 stands out as a versatile and powerful AV receiver that enhances home entertainment through its detailed sound reproduction, robust connectivity options, and user-friendly design. Whether for serious movie watching or casual music listening, the AVR 510 delivers an exceptional audio experience that is hard to match.