Hayter Mowers 510D

1.16 1.16

Speciﬁcations

ALL FIGURES ARE NOMINALLY QUOTED AT THE RATED ENGINE SPEED OF 2900 RPM

UNLESS OTHERWISE STATED.

Engine

Condor

Type: HONDA GX340 UT2

4 - stroke, overhead valve, 1 cylinder

Speed Rating: 2900 rpm (no load)

Power Rating: 6.5 kw (8.7 hp) @ 2900 rpm

Capacity: 337 cc

Air Cleaner: Dual element type.

Cooling System: Forced air

Oil Type: SAE 10W-30

Oil Capacity: 1.1 Litres

Fuel Type: Unleaded petrol

Fuel Capacity: 6.1 Litres

IMPORTANT - PREVENT DAMAGE: For further information regarding the engine, refer to the Engine

Manual.

Transmission System

Drive Type: Hydraulic static differential transaxle

Cutterhead Drive System

Power Unit Intermediate Drive: Single clutch V-belt drive with integral engine lockout switch sensor

Power Unit Final Drive: Twin V-belt via countershaft

Verge Drive: Triple V-belt via countershaft

Rotary Attachment: Swinging cutterblades attached to circular bottom plates on coupled gearboxes

with pulley brake.

SPECIFICATIONS

Contents

Main CONDOR HYDROSTATIC DRIVE Operators Manual Page Page Page 1.5 1.5 CONTENTS CONTENTS Page No. 1.6 1.6 CONTENTS CONTENTS Page No. Training Preparation 1.8 1.8 Preparation Continued Operation 1.9 1.9 Operation Continued Page 1.11 1.11 Decals A B C D E H F G Page 1.13 1.13 dB EC CONFORMITY INFORMATION Noise Levels Vibration Levels EC Declaration of Conformity Wear Hearing Protection EC DECLARATION OF CONFORMITY Serial No. 1.15 1.15 INTRODUCTION Introduction Page 1.17 1.17 Power Unit Specications SPECIFICATIONS Operator Controls Weight and Dimensions 1.18 1.18 Recommended Lubricants and Hydraulic Fluids SPECIFICATIONS Verge Attachments Rotary Attachments Page 1.20 1.20 Assembling the Cutterhead Attachment to the Power Unit ASSEMBLING THE MOWER Fig 2 Fig 1 1. Nut 2. Tensioning Bolt 3. Mounting Bolt 4. Washer 5. Nyloc Nut 1.21 1.21 Assembling the Cutterhead Attachment to the Power Unit continued ASSEMBLING THE MOWER 1.22 1.22 Safety Notice Operator Presence Control 1.23 1.23 Identication of Controls P Braking System Throttle Control Travel 1.24 1.24 Travel continued Transmission Bypass Valve Control 1.25 1.25 Ignition Switch Cutterhead Drive Operation Starting the Engine 1.26 1.26 Starting the Engine continued Stopping the Engine 1.27 1.27 General Operating Hints Adjusting Height of Cutter Page Page 1.30 1.30 Engine Running In Period - At First 50 Hours of Use 1.31 1.31 Running In Period - At First 50 Hours of Use continued Daily and Before Use 1.32 1.32 Daily and Before Use continued 1.33 1.33 Daily And Before Use continued 1.34 1.34 Every 50 Hours Lubrication 1.35 1.35 Every 200 Hours 1.36 1.36 Every 200 Hours continued 1.37 1.37 Every 200 Hours continued 1.38 1.38 Power Unit General Maintenance continued 1.39 1.39 Power Unit General Maintenance continued Verge Attachment 1.40 1.40 Verge Attachment continued 1.41 1.41 Verge Attachment continued Rotary Attachment 1.42 1.42 Rotary Attachment continued Cutterblades 1.43 1.43 PREPARING THE MOWER FOR STORAGE Preparing the Mower for storage 1.44 1.44 GRASS CUTTING FAULTS Rotary Attachment Verge Attachments 1.45 1.45 TROUBLE SHOOTING 1.46 1.46 TROUBLE SHOOTING 1.47 1.47 ELECTRICAL CIRCUIT DIAGRAM Black 1.48 1.48 WARRANTY