Hayter Mowers 510D 1.37 1.37, Every 200 Hours continued

1.37 1.37

MAINTENANCE

Every 200 Hours continued

- Top up the reservoir to the ‘’COLD’ level and

replace the cap. Clean off any surplus oil from

around the reservoir and the hydrostatic unit to

prevent a build up of debris.

The procedure has now been completed.

Note - The oil change procedure can be accom-

plished without removing the hydrostatic unit but

it will take an exceptionally long period to refill

the unit through the small diameter feed pipe.

Check all belt tensions: Refer to RUNNING IN

PERIOD.

Check cutterhead drive clutch cable adjust-

ment: Refer to RUNNING IN PERIOD.

Check condition of cutterhead drive brake pad:

Replace if excessively worn.

Check cutterhead drive brake adjustment:

Refer to RUNNING IN PERIOD.

Power Unit General Maintenance

Transmission bypass valve: The lever should be

adjusted so that the bypass valve plunger on the

hydrostatic unit is fully depressed when the lever

is just touching the handlebar cross-tube.

To adjust setting slacken adjuster nuts at end of

cable. Adjust cable setting and lock the adjuster

nuts. Check that the machine can be moved with

the engine switched off when the bypass valve

lever is operated.

Parking brake - cable adjustment: To adjust the

cable, slacken off the locknut and turn the cable

adjuster. A correctly set cable should have no

slack. When the brakes are applied, the brake lever

should operate smoothly and lock at the end of its

travel.

Check that the parking brake has been applied by

depressing the transmission bypass valve lever and

try to pull or push the machine. The wheels should

be locked. Re adjust the cable if the machine is

able to be moved. Tighten the cable adjuster lock-

nuts.

Contents

Main CONDOR HYDROSTATIC DRIVE Operators Manual Page Page Page 1.5 1.5 CONTENTS CONTENTS Page No. 1.6 1.6 CONTENTS CONTENTS Page No. Training Preparation 1.8 1.8 Preparation Continued Operation 1.9 1.9 Operation Continued Page 1.11 1.11 Decals A B C D E H F G Page 1.13 1.13 dB EC CONFORMITY INFORMATION Noise Levels Vibration Levels EC Declaration of Conformity Wear Hearing Protection EC DECLARATION OF CONFORMITY Serial No. 1.15 1.15 INTRODUCTION Introduction Page 1.17 1.17 Power Unit Specications SPECIFICATIONS Operator Controls Weight and Dimensions 1.18 1.18 Recommended Lubricants and Hydraulic Fluids SPECIFICATIONS Verge Attachments Rotary Attachments Page 1.20 1.20 Assembling the Cutterhead Attachment to the Power Unit ASSEMBLING THE MOWER Fig 2 Fig 1 1. Nut 2. Tensioning Bolt 3. Mounting Bolt 4. Washer 5. Nyloc Nut 1.21 1.21 Assembling the Cutterhead Attachment to the Power Unit continued ASSEMBLING THE MOWER 1.22 1.22 Safety Notice Operator Presence Control 1.23 1.23 Identication of Controls P Braking System Throttle Control Travel 1.24 1.24 Travel continued Transmission Bypass Valve Control 1.25 1.25 Ignition Switch Cutterhead Drive Operation Starting the Engine 1.26 1.26 Starting the Engine continued Stopping the Engine 1.27 1.27 General Operating Hints Adjusting Height of Cutter Page Page 1.30 1.30 Engine Running In Period - At First 50 Hours of Use 1.31 1.31 Running In Period - At First 50 Hours of Use continued Daily and Before Use 1.32 1.32 Daily and Before Use continued 1.33 1.33 Daily And Before Use continued 1.34 1.34 Every 50 Hours Lubrication 1.35 1.35 Every 200 Hours 1.36 1.36 Every 200 Hours continued 1.37 1.37 Every 200 Hours continued 1.38 1.38 Power Unit General Maintenance continued 1.39 1.39 Power Unit General Maintenance continued Verge Attachment 1.40 1.40 Verge Attachment continued 1.41 1.41 Verge Attachment continued Rotary Attachment 1.42 1.42 Rotary Attachment continued Cutterblades 1.43 1.43 PREPARING THE MOWER FOR STORAGE Preparing the Mower for storage 1.44 1.44 GRASS CUTTING FAULTS Rotary Attachment Verge Attachments 1.45 1.45 TROUBLE SHOOTING 1.46 1.46 TROUBLE SHOOTING 1.47 1.47 ELECTRICAL CIRCUIT DIAGRAM Black 1.48 1.48 WARRANTY