Hayter Mowers 510D

1.28 1.28

OPERATING THE MOWER

Adjusting Height of Cutter continued

30’’ Rotary Attachment.

Loosen hand knob (1) sufficiently to allow lever

(2) to be moved to the required height of cut posi-

tion. Retighten the hand knob to secure the height

of cut lever in position.

Handlebar Height Adjustment

The height of the handlebar may be adjusted at the

connection between the handlebar stays (1) and

the plate on the handlebar (2). Adjustment holes

(3) provide 3 alternative handlebar settings. Ensure

that the handlebars are set at the same level on each

side of the mower.

Note: The length of the connecting rods to the

travel control rocker levers must be re adjusted as

necessary to ensure correct operation.

1. Hand knob

2. Height of Cut Lever

1. Handlebar Stay

2. Handlebar

3. Adjustment Holes

Contents

Main CONDOR HYDROSTATIC DRIVE Operators Manual Page Page Page 1.5 1.5 CONTENTS CONTENTS Page No. 1.6 1.6 CONTENTS CONTENTS Page No. Training Preparation 1.8 1.8 Preparation Continued Operation 1.9 1.9 Operation Continued Page 1.11 1.11 Decals A B C D E H F G Page 1.13 1.13 dB EC CONFORMITY INFORMATION Noise Levels Vibration Levels EC Declaration of Conformity Wear Hearing Protection EC DECLARATION OF CONFORMITY Serial No. 1.15 1.15 INTRODUCTION Introduction Page 1.17 1.17 Power Unit Specications SPECIFICATIONS Operator Controls Weight and Dimensions 1.18 1.18 Recommended Lubricants and Hydraulic Fluids SPECIFICATIONS Verge Attachments Rotary Attachments Page 1.20 1.20 Assembling the Cutterhead Attachment to the Power Unit ASSEMBLING THE MOWER Fig 2 Fig 1 1. Nut 2. Tensioning Bolt 3. Mounting Bolt 4. Washer 5. Nyloc Nut 1.21 1.21 Assembling the Cutterhead Attachment to the Power Unit continued ASSEMBLING THE MOWER 1.22 1.22 Safety Notice Operator Presence Control 1.23 1.23 Identication of Controls P Braking System Throttle Control Travel 1.24 1.24 Travel continued Transmission Bypass Valve Control 1.25 1.25 Ignition Switch Cutterhead Drive Operation Starting the Engine 1.26 1.26 Starting the Engine continued Stopping the Engine 1.27 1.27 General Operating Hints Adjusting Height of Cutter Page Page 1.30 1.30 Engine Running In Period - At First 50 Hours of Use 1.31 1.31 Running In Period - At First 50 Hours of Use continued Daily and Before Use 1.32 1.32 Daily and Before Use continued 1.33 1.33 Daily And Before Use continued 1.34 1.34 Every 50 Hours Lubrication 1.35 1.35 Every 200 Hours 1.36 1.36 Every 200 Hours continued 1.37 1.37 Every 200 Hours continued 1.38 1.38 Power Unit General Maintenance continued 1.39 1.39 Power Unit General Maintenance continued Verge Attachment 1.40 1.40 Verge Attachment continued 1.41 1.41 Verge Attachment continued Rotary Attachment 1.42 1.42 Rotary Attachment continued Cutterblades 1.43 1.43 PREPARING THE MOWER FOR STORAGE Preparing the Mower for storage 1.44 1.44 GRASS CUTTING FAULTS Rotary Attachment Verge Attachments 1.45 1.45 TROUBLE SHOOTING 1.46 1.46 TROUBLE SHOOTING 1.47 1.47 ELECTRICAL CIRCUIT DIAGRAM Black 1.48 1.48 WARRANTY