5 Enter a maximum heart rate setting.
After you have |
|
|
|
| |||
|
|
|
|
|
| ||
entered your |
|
|
|
| |||
|
|
|
|
|
| ||
age, the letters |
|
|
|
| |||
|
|
|
|
|
| ||
PLS will appear |
|
|
|
|
|
| |
|
|
| |||||
in the Pulse dis- |
|
|
|
| |||
play. Press the |
|
|
|
| |||
+ or – button. A |
|
| |||||
number will then appear in the display. This num- |
|
| |||||
ber is the | maximum heart rate setting | for the pro- | |||||
gram. If Pulse program 1 is selected, the maxi- |
|
| |||||
mum heart rate setting can be from 65% to 85% |
|
| |||||
of your | maximum possible heart rate | ; if Pulse pro- | |||||
gram 2 is selected, the maximum heart rate set- |
|
| |||||
ting can be from 65% to 80% of your m | aximum | ||||||
possible heart rate. |
|
| |||||
Note: Your maximum possible heart rate is esti- mated by subtracting your age from 220. For ex- ample, if you are 30 years old, your maximum pos-
sible heart rate is 190 (220 – 30 = 190). Therefore, if Pulse program 1 is selected, the maximum heart
rate setting can be from 123 to 161 beats per
minute (65% of 190 is 123; 85% of 190 is 161).
If you want to change the maximum heart rate set- ting, press the + and – buttons. The buttons can be held down to change the setting quickly. When the desired setting is shown, press the Enter button.
Press the Start button or the Speed + button to
6 start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and incline settings for the program. Hold the handrails and begin walking.
Each program is divided into several time segments
of different lengths. (The Time/Segment Time dis- play will show both the time remaining in the pro- gram and the time remaining in the current seg- ment). One target heart rate setting is pro- grammed for each segment. The heart rate setting for the first
segment will
be shown in the flashing
Current Segment col- umn of the program dis- play. The heart rate
settings for the next several segments will be shown in the columns to the right.
When only three seconds remain in the first seg- ment of the program, both the Current Segment column and the column to the right will flash, a se- ries of tones will sound, and the Speed display and the Distance/Incline display will flash. When
the first segment is completed, | all heart rate | set- |
tings will move one column to the left | . The | heart |
rate setting for the second segment will then be shown in the flashing Current Segment column,
and th e speed and/or incline of the treadmill will change, if needed, to bring your heart rate closer to the heart rate setting for the second segment.
The program will continue until no time remains in the Time/Segment Time display. The walking belt will then slow to a stop.
If the speed or incline setting for the current seg- ment is too high or too low, you can adjust the set- ting with the Speed or Incline buttons. However, if
you | decrease |
| the speed, the incline will automati- | ||||
cally | increase | ; if you | increase | the speed, the in- | |||
cline will decrease | . If you | increase | the incline, the | ||||
speed will | decrease | ; if you |
| decrease | the incline, | ||
the speed will |
| increase | . The treadmill will always | ||||
attempt to keep your heart rate near the target |
| ||||||
heart rate setting for the current segment. |
| Note: | |||||
When the incline reaches the lowest setting, the |
| ||||||
speed cannot be increased any further. When the |
| ||||||
incline reaches the highest setting, the speed can- not be decreased any further.
If your pulse is not detected during the program, the letters PLS will flash in the Pulse display. In addition, the speed and/or incline of the treadmill may automatically decrease until your pulse is de- tected. If this occurs, refer to CHEST PULSE SEN-
SOR TROUBLESHOOTING on page 7.
Pulse programs cannot be stopped temporarily and then restarted. To stop the program at any time, press the Stop button.
7 Follow your progress with the displays.
See step 5 on page 12.
8 When the program has ended, remove the key.
See step 6 on page 14.
15
