Manuals / Hearth and Home Technologies / Household Appliance / Stove

Hearth and Home Technologies 21M-ACC Installing Chimney Components, Chimney Height / Rise and Run

Models: 21M-ACC

1 44
Download 44 pages 25.37 Kb
Page 16
Image 16

2100 Millennium Wood Stove (ACC)

R

Solid Pack Chimney with Metal Supports as a Thimble (Cont’d)

C. Installing Chimney Components

Chimney Connector

Single wall connector or stove pipe.

Min. Chimney Clearance to

Wall Spacer and

Combustibles - 2 inch (51mm)

Chimney Flue

Liner

Fireclay

Liner or

Equivalent

Masonry Chimney Constructed to NFPA 211

Min. Clearance 2 inch (51mm)

1 inch (25mm) Air Space to Chimney Section

Chimney

Connector

Chimney Section

Trim Collar

Wall Band

Wall Spacer

This must be at least 24 gauge mild steel or 26 gauge blue steel. The sections must be attached to the appliance and to each other with the crimped (male) end pointing toward the stove. All joints, including the connection at the flue collar, should be secured with 3 sheet metal screws. Make sure to follow the minimum clearances to combustibles. Where passage through the wall, or partition of combustible con- struction is desired in Canada, the installation shall conform to CAN/CSA-B365.

Factory-built listed chimney connector (vented).

A listed connector (vented) must be used when installing this unit in a mobile home. The listed connectors must conform to each other to ensure a proper fit and seal.

Figure 16.1

Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (420-480cm) high, (includes stove height) measured from the base of the appliance. The further your stack height or diameter varies from this configuration, the possibility of performance problems exists.

Chimney height may need to be increased by 2 - 3% per each 1000 feet above sea level. It is not recommended to use offsets or elbows at altitudes above 4000 feet above sea level or when there are other factors that affect flue draft.

Crimped

Flue Gas

End

Direction

Toward

 

Stove

 

Secure pipe sections with a

minimum of 3 screws

Figure 16.2 Chimney Connector (Stove Pipe)

WARNING

Fire Risk.

Inspection of Chimney:

•Chimney must be in good condition.

•Meets minimum standard of NFPA 211

•Factory-built chimney must be 6 inch (152mm) UL103 HT.

WARNING

Asphyxiation Risk.

•Do NOT connect this unit to a chimney flue servicing another appliance.

•Do NOT connect to any air distribution duct or system.

May allow flue gases to enter the house.

WARNING

Fire Risk.

Follow Chimney Connector Manufacturer’s

Instructions for Proper Installation.

ONLY use connector:

•Within the room, between appliance and ceiling or wall. Connector shall NOT pass through:

•Attic or roof space

•Closet or similar concealed space

•Floor or ceiling

Maintain minimum clearances to combustibles

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appli- ance. For assistance or additional information consult a qualified installer, service agency or your dealer.

Page 16

7039-131F

September 1, 2008

Page 15 Page 17
Page 16
Image 16
Hearth and Home Technologies 21M-ACC warranty Installing Chimney Components, Single wall connector or stove pipe
Page 15 Page 17

21M-ACC specifications

Hearth and Home Technologies' 21M-ACC model represents a significant advancement in the realm of modern home heating solutions. Designed for both aesthetic appeal and functional efficiency, this unit seamlessly integrates contemporary design with advanced technology.

The 21M-ACC is primarily known for its high efficiency, boasting an impressive thermal efficiency rating. This means less fuel is used to produce more heat, thereby reducing energy costs and consumption. One of the standout features is the high-efficiency combustion system that enhances the burning process, ensuring that the maximum amount of fuel is utilized before any emissions are released.

Another key characteristic of the 21M-ACC is its innovative AccuFire technology. This advanced control system allows users to finely adjust the flame height, heat output, and other parameters with precision. This level of customization not only enhances comfort but also contributes to energy savings. The model also features an easy-to-use digital control panel, enabling straightforward adjustments and monitoring of performance.

The design of the 21M-ACC is equally noteworthy. It showcases a sleek and stylish appearance that can complement various home décors, ranging from modern to rustic. The large viewing window provides an unobstructed view of the flames, creating a cozy ambiance while ensuring optimal heat distribution throughout the space.

Safety is paramount in the design of the 21M-ACC. It includes features such as a built-in safety shut-off system and a robust heat shield, which ensures that the exterior remains cool to the touch, making it safe for households with children or pets.

Additionally, this model is compatible with a variety of fuel types, including natural gas and propane, offering versatility for users. Whether utilizing it as a primary heat source or a supplementary feature, the 21M-ACC adapts to individual heating needs and preferences.

In conclusion, Hearth and Home Technologies' 21M-ACC combines efficiency, safety, and design sophistication, making it an exemplary choice for those looking to enhance their living space with a reliable heating solution.