5100-I ACT WOOD INSERT

R

C. Installing Chimney Components

required: A minimum NFPA 211 required stainless steel liner connector pipe extending to the first flue liner of the existing code approved masonry chimney. To eliminate dilu- tion air in the chimney, seal the damper area of the chimney around the chimney connector.

best: A complete relining of the chimney system with a 6 inch (152mm) diameter listed, stainless steel liner. The liner must be connected to the insert flue collar and extend the entire height of the chimney, terminating slightly above a plate that seals the top of the chimney. All joints should be secured with 3 sheet metal screws. The sections must be attached to the insert and to each other with the crimped (male) end point- ing toward the insert. Figure 15.1.

Minimum clearances to combustibles must be maintained.

A full reline is required for factory-built fireplace installations in Canada and is highly recommended in USA.

LINER CONNECTOR

CRIMPED

FLUE

END

GAS

TOWARDS

DIRECTION

STOVE

 

Figure 15.1

Ovalizing Round Stainless Steel Liners

Ovalizing round stainless steel liners to accommodate the liner passing through the damper region of a fireplace is an allowable and acceptable practice.

Ensure that the ovalization is minimized to the extent required to fit through the damper.

WARNING

Fire Risk.

Do NOT pack insulation or other combustibles between spacers.

ALWAYS maintain specified clearances around venting and spacers.

Install spacers as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

Air Clearances

To ensure that insulation or any other combustible material does not contact the chimney, a chimney inside the house must have at least 2 inches (51mm) of air space clearance around the chimney. A chimney outside the house must have at least 1 inch (25mm) clearance to the combustible structure. Noncombustible fire stops must be installed at the spaces where the chimney passes through floors and/or ceil- ings. Figures 15.2 and 15.3.

Minimum 2 inch (51mm) clearance from combustible material

and insulation

ceiling

Non-combustible fire stopping material

Figure 15.2

 

Firestopping

Non-Combustible

 

Firestopping

 

Material

Floor

 

2inch (51mm)

Ceiling

Floor

Caulk

 

(second Story)

Minimum 1 inch (25mm)

 

 

clearance from exterior

 

chimney to sheathing

 

 

Figure 15.3

 

September 1, 2008

438-0380D

Page 15

Page 15
Image 15
Hearth and Home Technologies 5100I-NL-B, 5100I-GD-B Installing Chimney Components, Ovalizing Round Stainless Steel Liners

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.