R

5100-I ACT WOOD INSERT

 

 

 

 

 

 

 

 

 

 

 

Appliance Set-up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installation Outline

 

C. Panel & Trim Set Installation

 

 

 

 

Standard Size: 30-1/2” h x 47” w

 

A.7

 

 

 

1.

Record serial number on back cover of manual.

Large Size: 34-1/4” h x 51-1/4” w

 

2.

Remove the leveling bolts from the component pack and

 

Kit Includes:

Tools Needed:

 

 

 

start the bolts in the weld nuts. Figure 20.1

 

 

3.

Position insert on hearth with rear of insert extending into

(2) Side panels, left & right

Screwdrivers:

 

(1) Panel top & fastener package

Powered Phillips head

 

 

 

fireplace opening. Slide insert on its base into the open-

(2) Side trim, left & right

Long-handled Phillips head

 

 

 

ing leaving approximately 4 inches (102mm) protruding

(1) Trim top & fastener package.

 

 

out the front.

4.Assemble the panels and temporarily attach to insert.

Push insert into opening leaving 1 inch (25mm) protrud- ing out the front. Confirm the panel size is correct for the opening and that the face can be sealed off from room air when installation is complete. Figure 20.2 & 20.3.

5.Remove the panels and secure liner to the chimney ring.

6.Level the insert in its final position in the fireplace. If an offset adapter is required for installation, install it first and then secure liner to offset adapter.

7.Install the Panel & Trim set and (if applicable) the Zero

Clearance Trim Support.

1.Attaching Panels to the Insert

a.Loosely install the 2 side panels, do not tighten, using the cage nuts already attached to the appliance. (Note: The sides are not interchangeable). Figure

20.3.

b.Put top panel in place pushing straight back and then to the right to lock onto top of side panels. Attach the top panel to the sides using the panel brackets included in the fasteners package. Figure 20.2

c.Tighten side panels to the appliance using a long- handle screw driver.

B. Leveling Bolts

Two leveling bolts, 3/8” x 4” are shipped inside the com- ponent pack found inside the firebox.

NOTE: Not all installations will require the use of the level- ing bolts.

1.Remove the bolts from the component pack and insert into weld nuts welded to each side of the insert bottom

Figure 20.1

2.After securing the liner to the flue collar (or offset adapter) and the insert is in its final position, extend bolts down- ward to level insert.

Panel brackets

Do not tighten sides until top is locked into place

,EVELINGI"OLT

Figure 20.1

Figure 20.2

Back view of top and side panel assembled

Cage nut

Panel bracket

Figure 20.3

Page 20

438-0380D

September 1, 2008

Page 20
Image 20
Hearth and Home Technologies 5100I-GD-B, 5100I-NL-B Appliance Set-up, Installation Outline Panel & Trim Set Installation

5100I-NL-B, 5100I-GD-B specifications

Hearth and Home Technologies has established itself as a leader in the home heating industry, offering a wide range of high-quality fireplaces. Among their standout products are the 5100I-GD-B and 5100I-NL-B models. These two direct vent gas fireplaces not only enhance the aesthetics of a home but also provide efficient heating solutions.

The 5100I-GD-B model boasts a contemporary design that fits well in modern interiors. Equipped with a glass front, it allows for an unobstructed view of the flames, creating a cozy atmosphere in any space. The unit's high-efficiency burner maximizes heat output while minimizing gas consumption, making it an eco-friendly choice for homeowners. Additionally, the electronic ignition system ensures reliable startups, while the integrated control panel offers easy adjustments for flame height and heat settings.

On the other hand, the 5100I-NL-B model presents a more traditional design, featuring a clean face that blends seamlessly with various décor styles. Like its counterpart, this model is also engineered for efficiency, offering an impressive Annual Fuel Utilization Efficiency (AFUE) rating. This makes it an excellent choice for those looking to reduce energy costs without sacrificing comfort. The 5100I-NL-B is also equipped with an advanced combustion system that ensures complete fuel combustion, resulting in fewer emissions and a cleaner burn.

Both models feature optional accessories, including decorative media options like logs or stones, allowing homeowners to customize the look of their fireplaces. The direct vent system allows for easy installation in various locations, as it vents gases directly outside, ensuring indoor air quality is maintained.

Safety is a priority with Hearth and Home Technologies, and both models come with a safety screen and an automatic shut-off feature. This ensures peace of mind while enjoying the warmth and ambiance these fireplaces provide.

Overall, the Hearth and Home Technologies 5100I-GD-B and 5100I-NL-B gas fireplaces exemplify the perfect blend of functionality and style, making them ideal choices for anyone looking to enhance their home's heating options. With their impressive features and efficient performance, these models are designed to keep homes warm and inviting while offering options to match personal tastes.