6000GLX-IPI-R,-S | Hearth and Home Technologies 6000GLX-IPI-S

Service Parts	6000GLX-IPI-R,-S

Valve Assembly Diagram/ Parts List	Beginning Manufacturing Date: May 2006
	Ending Manufacturing Date: ______

Intermittent Pilot Ignition

Valve Assembly

1

21

20

19

		2	18
		2
	6	3	17
		5	17


			4
			15
			16
			14
			13
			12

9

8

10

11

Part number list on following page.

70	Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. S • 12/08

Image 70

Hearth and Home Technologies 6000GLX-IPI-S, 6000GLX-IPILP-S, 6000GLX-IPILP-R owner manual 6000GLX-IPI-R,-S

Contents

What to do if you smell gas Hot glass will cause burns Congratulations Homeowner Reference Information Table of Contents User Guide Finishing Appliance SetupTroubleshooting Reference Materials CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Lighting Instructions IPI Turn off all electric power to the applianceOn position. The ON/OFF switch may Final inspection by Frequently Asked Questions After Fireplace is Lit Maintenance and Service Venting Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection Logs IPI Pilot Flame Patterns Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a ﬁre hazard Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase Clearances Combustible Mantels Mantel and Wall ProjectionsCombustible Mantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances Covered Alcove Applications Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows V1 Minimum H1 Maximum Vent Diagrams Top Vent Horizontal TerminationV1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Three Elbows Min Max Break Here Two Elbows Top Vent Vertical TerminationMaximum + V 2 Min Top Vent Vertical Termination Three Elbows H1 + H2 V1 + V2 Minimum H1 + H2 MaximumPage H1 Maximum V1 Minimum H1 + H2 Maximum Rear Vent Horizontal Termination Two ElbowsH1 Maximum V1 Minimum H2+ H3 H1+ H2+ H3 Max Rear Vent Vertical Termination One Elbow H1 + H2 Maximum V1 Minimum Rear Vent Vertical Termination Three Elbows V1 Minimum H1 + H2 + H3 Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Pipe DVP SLP Flat Ceiling Installation Install Attic Insulation ShieldInstalling the Optional Heat-Zone-Gas Kit Vaulted Ceiling Installation Choosing the Top or Rear Vent Appliance PreparationProceed to . C Installing the Non-combustible Board Rear Vent Securing and Leveling the Appliance Assemble Vent Sections DVP Pipe Only Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Install Metal Roof Flashing Assemble and Install Storm Collar Install RF4-8 SLP-FS Install Decorative Wall Components SLP only Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination Ansi Z223.1 and CAN/CGA-B149 installation codes Install Horizontal Termination Cap DVP and SLP PipeRefer to of this manual Gas Pressure Gas InformationFuel Conversion Gas Connection Optional Accessories Requirements Wiring RequirementsIntelliﬁre Ignition System Wiring Electrical Information Electrical Service and Repair Intelliﬁre Pilot Ignition IPI Wiring Diagram Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing Material Doors Finish Door FIT Material See Maximum Thickness Appliance Setup Ember Placement Placement of Embers Log Assembly LOGS-6000GLX LOGS-6000GLXLP Install the Log Assembly 11 Front View 17 Front View Air Shutter Setting Install the MeshInstall Trim and/or Surround Air Shutter Settings Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramLocation Inches Millimeters Vent Components Diagrams DVP vent components Horizontal Termination Cap DVP vent components 302 mm 787 mm 13-1/4 367 mm 24-5/8 625 mm 27-1/2 127 mmRoof Flashing Multi-pak 13-3/4 11-7/8 349 mm 13-3/4 13-7/8 352 mm 349 mm DVP-TVHW DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAP Elbow 165 mm165 mm 222 mm 235 mm 152 mm 168 mm 251 mm Cathedral Ceiling Vertical Snorkel Support Box-BlackBlack Termination Cap Log Set Assembly Service Parts Stocked Service Parts ListAt Depot 6000GLX-IPI-R,-S 6000GLX-IPI-R,S Contact Information