Hearth and Home Technologies C-40 warranty Clear Space Near the Fireplace, Firescreen, Glass Doors

D. Clear Space Near the Fireplace

Combustible materials must not be stored on the hearth ex- tension. Room furnishings such as drapes, curtains, chairs or other combustibles must be at least 4 ft (1219mm) from the open front of the fireplace.

E. Firescreen

A firescreen is optional to control sparks. It must be in place whenever the fireplace is in use. Glass doors or firescreens must not be used to hold burning material inside the fire- place. Only those glass doors specifically tested and listed for use with the specific fireplace model should be used.

Use both hands to stabilize the screen. Ensure that the screen is fully attached. Be careful not to stack wood close to the front or too high that logs could roll out the front. Start with a small fire and adjust your heat to desired setting. If smoke spillage occurs, put on gloves and then remove the screen and close the doors. Refer to Troubleshooting Draft Problems on page 54.

WARNING

Fire Risk

•Close firescreen when burning fireplace.

•Do not use firescreen or glass doors to hold burning material in fireplace.

Firescreen controls sparks.

Glass may break or burning material may roll out.

•Always wear gloves when installing or removing the screen as the screen may become extremely hot while in use.

F.Glass Doors

This fireplace has been tested and listed for use with doors as specified in Section 12.D. Please refer to the manual packed with each set of doors for installation instructions.

WARNING

Fire Risk

Smoke Risk

•Doors must be fully opened or fully closed when operating fireplace.

Partially opened doors may draw flame, smoke or heat from fireplace.

G. Fan Operation

Instructions with Fan Override Switch in manual posi- tion.

1.Initial (cold) Startup: Leave fan off until your fire- place is hot and a good coal bed is established, ap- proximately 30 minutes after fuel is lit.

2.High Burn Setting: The fan may be left on throughout the burn.

3.Medium or Medium High Burn Setting: The fan should be left off until a good burn is established, then turned on medium or high rate.

4.Low Burn Setting: The fan tends to cool off the fire- place. Leave fan off until the burn is well established; then, if you wish, turn the fan on at a low rate.

NOTE: The fan is equipped with a snap disc that will turn the fan on and off depending on the temperature of the fire- place. If the fan is not coming on at the desired time, flip the override switch to manual and operate the fan as described above.

The override switch and the fan speed control are hard wired at time of installation and installed in a standard wall mount with junction box on the wall.

H. Heat Zone Operation

The Heat-Zone accessory kit conveys warm air from the fireplace through air duct(s) to remote locations in the same room or other rooms of the building. You may install 1 or 2 Heat-Zone kits on the fireplace. Follow the instructions that is supplied with the kit. Installation of this kit MUST be performed by a qualified service technician. If any parts are missing or damaged, contact your local dealer before starting installation. DO NOT install a damaged kit.

The Heat-Zone kit is carefully engineered and must be installed only as specified. If you modify it or any of its com- ponents, you will void the warranty and you may possibly cause a fire hazard. Installation must be done according to applicable local, state, provincial, and/or national codes.

DUCT RUN REQUIREMENTS

MAXIMUM Duct Run = 40 ft. (12m)

MINIMUM Duct Run = 36 in. (914mm)

DUCTING MATERIAL

6 in. (152mm) B-Vent Only

DO NOT DUCT into existing furnace plenum

MINIMUM CLEARANCE TO COMBUSTIBLE 1 in. (25mm) from the B-Vent

1/2 in. (13mm) from top and bottom of outlet box 0 in. (0mm) from the sides of outlet box

12 in. (305mm) from wall register to ceiling

Page 46 Heatilator • Constitution EPA Fireplace • 480-1091C November 11, 2008