CL36D AND CR36D INSTALLATION INSTRUCTIONS

9. Marking the Exit Point of the Roof

Locate the point where the chimney will exit the roof by plumbing down to the center of the chimney. Drive a nail up through the roof to mark the center. See Figure 12.

10.Cutting out the Hole in the Roof

Measure to either side of the nail and mark the 14½” x 14½” opening required. This is measured on the horizontal; actual length may be larger depending on the pitch of the roof. Cut out and frame the opening. See Chapter 25 of the Uniform Building Code for

Roof Framing Details.

Be sure to maintain a 2” minimum air space between the chimney section and the roof.

11.Assembling the Chimney Sections Through the Roof

Continue to add chimney sections through the roof opening, maintaining at least a 2” air space.

12.Installing the Roof Flashing

If a roof flashing is to be used, install the roof flashing appropriate to the roof pitch and install a round termination cap following the instructions shipped with the cap.

For chase installations you can use a round termination cap (TR344), a round telescoping termination cap (TR342) or a square termination cap (ST375/TS345/TS345P). A chase installation must use a chase top. Chase tops are available from your Heatilator distributor. See page 22 for building a chase.

13.Installing the Outside Air Kit

The outside air kit is supplied as a standard feature with this fireplace and its use is highly recommended to minimize the effects of negative pressure within the structure. It is recommended to utilize the shortest duct run to optimize the performance of the outside air kit. The outside air kit inlet thimble should be positioned at least four feet above the ground level, in a manner that will not allow snow, leaves, etc. to block the inlet.

The outside air kit is installed on the left hand side of the fireplace. Remove the cover plate from the side of the fireplace assembly where the air kit is to be installed. See Figure 13 for handle location/operation.

14.Installing the Chimney Air Kit

When installing the chimney air kit, follow the instructions provided with this accessory.

Figure 12 - Ceiling/Attic Construction

Figure 13 - Air Kit Handle Location

12538 Rev D

18

02-02

Page 17 Page 19
Page 18
Image 18
Hearth and Home Technologies CR36D, CL36D manual Marking the Exit Point of the Roof, Cutting out the Hole in the Roof
Page 17 Page 19

CR36D, CL36D specifications

Hearth and Home Technologies (HHT) has long been a leader in the fireplace market, and their CL36D and CR36D models exemplify the company's commitment to quality and innovation. Both models are part of the brand's extensive range of gas fireplaces, designed to offer an efficient and aesthetic heating solution for modern homes.

The CL36D, known for its linear design, measures 36 inches wide and is ideal for creating a stunning focal point in any living space. Its contemporary aesthetic features a clean face and a wide viewing area, allowing for an unobstructed view of the flames. The CR36D, on the other hand, brings a traditional touch with its classic stove-like appearance. This model can seamlessly integrate into various interior designs, catering to homeowners looking for a more classic or rustic focal point.

One of the standout features of both the CL36D and CR36D is their advanced burner technology. HHT has implemented a unique burner design that provides a realistic flame presentation, enhancing the overall ambiance of the space. These models also come equipped with an efficient heating system, capable of warming a substantial area while maintaining energy efficiency. The fireplaces utilize propane or natural gas as a fuel source, providing convenience and ease of use.

Another significant characteristic of these units is their versatility. Both the CL36D and CR36D can be customized with various media options, including traditional logs, glass beads, or contemporary stones. This flexibility allows homeowners to personalize their fireplace to match their unique style and preferences.

Safety features are also a priority for Hearth and Home Technologies. Both fireplaces are equipped with a safety shut-off system, ensuring that the unit will turn off in case of any malfunctions. Additionally, they can be integrated with optional remote controls and wall switches, allowing for easy operation from anywhere in the room.

In summary, the Hearth and Home Technologies CL36D and CR36D offer a blend of contemporary and traditional designs, advanced burner technology, energy efficiency, and customizable features. Whether you prefer a sleek, modern look or a more classic style, these models provide an exceptional heating solution while enhancing the aesthetic appeal of your home. With their impressive safety features and user-friendly operation, the CL36D and CR36D are excellent choices for anyone looking to invest in a high-quality gas fireplace.
Top Page Image Contents