Hearth and Home Technologies EL36 Series, EL42 Series specification

F. Tools and Supplies Needed

Before beginning the installation be sure the following tools and building supplies are available:

Reciprocating saw	Framing material
Pliers	Non-combustible sealant
Hammer	Gloves
Phillips screwdriver	Framing square
Flat blade screwdriver	Electric drill and bits
Plumb line	Safety glasses
Level	Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws Misc. screws and nails

G. Fireplace System Requirements

This ﬁreplace system requires:

•Fireplace

•Hearth Refractory

•Grate Assembly

•Hearth Extension (required, sold separately)

•Chimney Air Kit (required in Canada)

•Chimney System (required, sold separately)

•Termination Cap (required, sold separately)

H. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged parts could impair safe operation. DO NOT install dam- aged, incomplete or substitute components. Keep ﬁre- place dry.

•Remove ﬁreplace and components from packaging and inspect for damage.

•Vent system components and doors are shipped in separate packages.

•Report to your dealer any parts damaged in shipment.

•Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and beneﬁt.

Heatilator • EL36/EL42 • 4044-132 • Rev V • 11/08

17

Image 17

Hearth and Home Technologies EL36 Series, EL42 Series owner manual Tools and Supplies Needed, Fireplace System Requirements

Contents

Operation Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Fire Risk Number Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited Warranty Heatilator EL36/EL42 4044-132 Rev V 11/08 Appliance Certiﬁcation Listing and Code ApprovalsNon-Combustible Materials Combustible Materials Hot glass will cause burns Operating InstructionsYour Fireplace Starting a Fire Seasoned WoodGrate Firescreen Vented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear Space Wood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for Removal Check Firebox Refractory Glass CleaningInspect Grate Frequency As desired Start Fire Problems Possible Cause Solution Troubleshooting Guide Getting Started Installer Guide Negative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & Chimney Inspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Mm all configurationsFraming & Clearances Clearances to Combustible Materials Clearances Frame the Fireplace Fireplace Outside Model # Opening DimensionsSidewalls/Surrounds Things to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth Strips YES Ft min. from top of uppermost chimney section to air inlet Outside Air Installation Install Outside Air Kit Maintain minimum height of chimney above roof Chimney Assembly Height of Chimney Components Chimney Requirements Example Using Offsets/Returns Assemble Chimney Sections Install Chimney Air Kit Installing the Ceiling Firestop Install Ceiling Firestops Prepare Attic Insulation Shield Install Attic Insulation Shield Install Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in Roof Flat Roofs Chimney Termination Requirements Construct the Chase Chase InstallationsGas line holes and other openings should be caulked with Chase should be constructed in the manner of all Install as per Sections 7 Install Fireplace & ChimneyInstall Chase Top ST375 Square Termination Cap Install Termination Cap TCT375 Terra Cotta Cap TS345/TS345P Square Termination Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR342 caps require radiation shield Roofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield required Hearth Extension Finishing= 1/k x inches of thickness Refer to .2 for hearth extension insulation alternatives Minimum between Raised Hearth Extension Framing Noncombustible Finishing Materials Non-combustible Sealant In. Micore or equivilent insulation Finishing Material Clearances to Mantels or other Combustibles above Fireplace Combustible Mantel Model Outside Di- mensions Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1 Reference Materials Fireplace Dimensions 1676 mm 508 mm 13 mm 1321 mm 406 mmID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated Duct Air Kit Parts Catalog # Chimney Components 10-1/2 267 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm305 mm 27-3/8 24-5/8 695 mm 625 mm 305 mm 24-5/8 625 mm 787 mm 10-7/8 276 mm Rev V 11/08 Service PartsHeatilator EL36/EL42 EL42 Contact Information