Clearances | Hearth and Home Technologies EL36 Series, EL42 Series

B. Clearances

WARNING! Risk of Fire! You must comply with all minimum air space clearances to combustibles as speciﬁed in Fig- ure 6.2. DO NOT pack required air spaces with insulation or other materials.

Storm Collar

Roof Flashing

(attic)

(insulation)

2 in. (51 mm) min.

Shaded areas

represent

2 in. (51 mm) min. air space clearance required around pipe

Attic

Insulation

Shield

(ceiling)

Offset/Return (secured

with hanger straps)

(ceiling)

Ceiling Firestop

0 in. to level of standoffs

Must have 2 in. (51 mm)

minimum clearance

to header

Combustible Object

48 in. 1219 mm

1/2 in. (13 mm) to back & sides of appliance

0in.

to floor

Figure 6.2 Clearances to Combustible Materials

Note: Chimney air kit is not shown, but is required in Canada.

Heatilator • EL36/EL42 • 4044-132 • Rev V • 11/08

Page 19

Image 19

Hearth and Home Technologies EL36 Series, EL42 Series owner manual Clearances to Combustible Materials

Contents

Fire Risk Wood Burning FireplaceOperation Hot screen/mesh and glass doors will cause burns Grate Listing Label Information/LocationNumber Installer Guide Table of ContentsUser Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited Warranty Heatilator EL36/EL42 4044-132 Rev V 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certiﬁcation Non-Combustible Materials Your Fireplace Operating InstructionsHot glass will cause burns Firescreen Seasoned WoodStarting a Fire Grate Clear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional Components Wood Fuel Creosote Formation and Need for Removal Maintainance and ServiceChimney Inspection/Cleaning Disposal of Ashes Frequency As desired Glass CleaningCheck Firebox Refractory Inspect Grate Start Fire Problems Possible Cause Solution Troubleshooting Guide Getting Started Installer Guide Draft Design and Installation ConsiderationsNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & Chimney Fireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Mm all configurationsSelect Fireplace Location Clearances to Combustible Materials Clearances Sidewalls/Surrounds Fireplace Outside Model # Opening DimensionsFrame the Fireplace Place Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the Fireplace YES Ft min. from top of uppermost chimney section to air inlet Outside Air Installation Install Outside Air Kit Maintain minimum height of chimney above roof Chimney Assembly Height of Chimney Components Chimney Requirements Example Using Offsets/Returns Assemble Chimney Sections Install Chimney Air Kit Installing the Ceiling Firestop Install Ceiling Firestops Prepare Attic Insulation Shield Install Attic Insulation Shield Cut out Hole in Roof Complete InstallationInstall Flashing Following steps should be skipped if using a chase Flat Roofs Chimney Termination Requirements Chase should be constructed in the manner of all Chase InstallationsConstruct the Chase Gas line holes and other openings should be caulked with Install Chase Top Install Fireplace & ChimneyInstall as per Sections 7 ST375 Square Termination Cap Install Termination Cap TCT375 Terra Cotta Cap TS345/TS345P Square Termination Cap Open Top Shroud TR342 caps require radiation shield ShroudsRadiation Shield Field Constructed Shrouds Roofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield required Refer to .2 for hearth extension insulation alternatives FinishingHearth Extension = 1/k x inches of thickness Minimum between Raised Hearth Extension Framing Noncombustible Finishing Materials Non-combustible Sealant In. Micore or equivilent insulation Finishing Material Clearances to Mantels or other Combustibles above Fireplace Combustible Mantel Model Outside Di- mensions Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning Inserts Reference Materials Fireplace Dimensions Air Kit Parts 1321 mm 406 mm1676 mm 508 mm 13 mm ID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated Duct Catalog # Chimney Components 305 mm 24-5/8 625 mm 787 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 27-3/8 24-5/8 695 mm 625 mm 10-7/8 276 mm Heatilator EL36/EL42 Service PartsRev V 11/08 EL42 Contact Information

Hearth and Home Technologies EL36 Series, EL42 Series Clearances to Combustible Materials

Models: EL42 Series EL36 Series

B. Clearances

Figure 6.2 Clearances to Combustible Materials

Heatilator • EL36/EL42 • 4044-132 • Rev V • 11/08