Install Chase Top | Hearth and Home Technologies EL36 Series

B. Install Fireplace & Chimney

Install as per Sections 7 and 8.

C. Install Chase Top

•You MUST use a chase top in a chase installation. Chase tops are available from your Heatilator dealer or may be ﬁeld constructed.

•Include a turndown and drip edge to prevent water from seeping into the chase.

•Include a 2 in. (51 mm) soldered, welded or spun collar around pipe opening to keep water out.

•Provide a 1/8 in. (3 mm) gap around the ﬂue pipe.

•Slope the chase top downward away from the opening.

WARNING! Risk of Fire! DO NOT caulk the pipe to the chase top collar.

•Caulk all seams to prevent leaks.

•Refer to Figure 9.3.

Slope Downward (1/4 in. per foot minimum)

2 in. (51 mm) Collar on Chase Top

Turn-down

Drip Edge

Chase

.018 (26 ga) min. Galvanized Chase Top

Figure 9.3 Chase Top Construction

Heatilator • EL36/EL42 • 4044-132 • Rev V • 11/08

Page 33

Image 33

Hearth and Home Technologies EL36 Series Install Fireplace & Chimney, Install Chase Top, Install as per Sections 7

Contents

Operation Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Fire Risk Listing Label Information/Location GrateNumber Table of Contents Installer GuideUser Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited Warranty Heatilator EL36/EL42 4044-132 Rev V 11/08 Appliance Certiﬁcation Listing and Code ApprovalsNon-Combustible Materials Combustible Materials Operating Instructions Your FireplaceHot glass will cause burns Starting a Fire Seasoned WoodGrate Firescreen Vented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear Space Wood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for Removal Check Firebox Refractory Glass CleaningInspect Grate Frequency As desired Start Fire Problems Possible Cause Solution Troubleshooting Guide Getting Started Installer Guide Design and Installation Considerations DraftNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & Chimney Tools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Mm all configurations Framing & ClearancesSelect Fireplace Location Clearances to Combustible Materials Clearances Fireplace Outside Model # Opening Dimensions Sidewalls/SurroundsFrame the Fireplace Things to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth Strips YES Ft min. from top of uppermost chimney section to air inlet Outside Air Installation Install Outside Air Kit Maintain minimum height of chimney above roof Chimney Assembly Height of Chimney Components Chimney Requirements Example Using Offsets/Returns Assemble Chimney Sections Install Chimney Air Kit Installing the Ceiling Firestop Install Ceiling Firestops Prepare Attic Insulation Shield Install Attic Insulation Shield Install Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in Roof Flat Roofs Chimney Termination Requirements Construct the Chase Chase InstallationsGas line holes and other openings should be caulked with Chase should be constructed in the manner of all Install Fireplace & Chimney Install Chase TopInstall as per Sections 7 ST375 Square Termination Cap Install Termination Cap TCT375 Terra Cotta Cap TS345/TS345P Square Termination Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR342 caps require radiation shield Roofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield required Hearth Extension Finishing= 1/k x inches of thickness Refer to .2 for hearth extension insulation alternatives Minimum between Raised Hearth Extension Framing Noncombustible Finishing Materials Non-combustible Sealant In. Micore or equivilent insulation Finishing Material Clearances to Mantels or other Combustibles above Fireplace Combustible Mantel Model Outside Di- mensions Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1 Reference Materials Fireplace Dimensions 1676 mm 508 mm 13 mm 1321 mm 406 mmID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated Duct Air Kit Parts Catalog # Chimney Components 10-1/2 267 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm305 mm 27-3/8 24-5/8 695 mm 625 mm 305 mm 24-5/8 625 mm 787 mm 10-7/8 276 mm Service Parts Heatilator EL36/EL42Rev V 11/08 EL42 Contact Information