Hearth and Home Technologies SMART-STAT-II Transmitter Safety Features, System Check

Child Proof Lockout (CP)

The transmitter contains a “Child Proof” lockout feature that prevents unauthorized use of the remote control. To access the “Child Proof” activation button, remove cover on BACK of transmitter. To activate LOCKOUT:

1.Press and hold in the “setting button” for 5 sec- onds. The letters CP will display on the LCD screen (see Figure 6). This prevents the activation of fire- place. When any function button is pressed ON/ OFF etc. the letter CP will display on the LCD screen.

To deactivate LOCKOUT:

1.Press and hold in the “setting button” for 5 sec- onds. The LCD will display CP until 5 seconds have elapsed, and then the LCD screen will return to its normal state.

TRANSMITTER SAFETY FEATURES

It is recommended that the TRANSMITTERS always be located within a 20 foot operating range of the fireplace, preferably in the same room in which the fireplace sys- tem is located. The TRANSMITTER features several safety features that alert the user when the TRANSMIT- TER is placed outside the 20 foot normal operating range.

Communication-Safety Features

This remote control has a COMMUNICATION-SAFETY function built into its software. It provides an extra mar- gin of safety when the TRANSMITTER is out of the nor- mal 20 foot operating range of the receiver. It is also activated when the batteries become weak or are re- moved from the transmitter.

In the THERMO-UPDATING feature (only in the THERMO or TIMER modes) the transmitter normally reads the ROOM temperature every 2 minutes. In addi- tion to checking the temperature, the transmitter sends a signal to the receiver indicating that the transmitter and its batteries are still active.

In the COMMUNICATION-SAFETY feature, at all times and in all OPERATING MODES the transmitter sends a signal every fifteen (15) minutes to the receiver, indicat- ing that the transmitter is within the normal operating range of 20 feet.

Should the receiver NOT receive a transmitter signal every 15 minutes (COMMUNICATION-SAFETYfeature), the RE- CEIVER will begin a 2 HOUR (120 minute) countdown timing function. If during this 2 hour period, the receiver does not receive a signal from the transmitter, the RE- CEIVER will shut down the fireplace being controlled by the receiver. The RECEIVER will then emit a series of rapid “beeps”. Then, after 10 rapid “beeps”, the RECEIVER will continue to emit a single “beep” every 4 seconds until a transmitter signal is again received. The intermittent 4 seconds beeping will go on indefinitely until reset.

To “reset” the RECEIVER and operate the fireplace system:

1.Press the MODE button on the transmitter. The word ON must display on the LCD screen. The COM- MUNICATION -SAFETY operation is overridden and the system will return to normal operation depend- ing on the MODE selected at the transmitter.

We recommend the user check the batteries in the TRANSMITTER to make sure the voltage is no less than 2.7 volts.

Auto Shutdown

This remote control has an Auto Shutdown feature in- corporated into its system. When the transmitter MODE is in the ON position the fireplace will continuously op- erate for 9 hours. After 9 hours, the fireplace will shut down. To relight the fireplace:

1. Press the MODE button.

The Auto Shutdown signal comes from the transmitter. The transmitter must be positioned within a 20 foot op- erating range for the Auto Shutdown feature to operate.

SYSTEM CHECK

Millivolt Valves

Light the appliance following the lighting instructions that came with the fireplace. Confirm that the pilot flame is on. It must be in operation for the main gas valve to operate.

1.Slide the 3-position button on the remote receiver to the ON position. The main gas flame (i.e., the fire) should ignite.

2.Slide the button to OFF. The flame should extinguish (the pilot flame will remain on).

3.Slide the button to REMOTE (the center position), then press the MODE button on the transmitter to change the system to ON. The main gas flame should ignite.

4.Press the MODE button on the transmitter to change the system to OFF. The flame should extinguish (the pilot flame will remain on).

5.Press the MODE button on the transmitter to change the system to THERMO.

6.Advance the SET temperature on the transmitter to a temperature of at least 20 F (10 C) above the ROOM temperature displayed on the LCD screen and the system flame will ignite.

7.Set the SET temperature to at least 20 F (10 C) below the room temperature and the system flame will ex- tinguish. Thereafter, it should continue to cycle on and off thermostatically approximately every two min- utes as the ROOM temperature changes, but only when the temperature differential between ROOM and SET temperatures differs at least 20 F (10 C). The 20 F (10 C) F differential is the factory setting.

6