Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 36DV manual V Ft, H Ft, VENTING WITH THREE 3 90 ELBOWS, H + H1

Models: 36DV

1 26

Download 26 pages 27.68 Kb

Page 15

Image 15

V (FT.)

H (FT.)

1.5' MIN. (.457m)

2.5' MAX. (.762m)

MIN. (.609m)

3' MAX. (.912m)

2.5'

MIN. (.762m)

6' MAX. (1.82m)

3.5'

MIN. (1.06m)

9' MAX. (2.73m)

4.5'

MIN. (1.37m)

12' MAX. (3.64m)

NOTE: H + H1 = 24' MAX. (7.28m)

V + V1 + H + H1= 64' MAX. (19.5m)

VENTING WITH THREE (3) 90° ELBOWS

NOTE: Must have a 12” minimum vertical vent before attaching a 90o elbow to the unit.

V (FT.)		H + H1	(FT.)
1.5' MIN. (.457m)		2.5' MAX.	(.762m)
2'	MIN. (.609m)	3' MAX. (.912m)
2.5'	MIN. (.762m)	6' MAX. (1.82m)
3.5'	MIN. (1.06m)	9' MAX. (2.73m)
4.5'	MIN. (1.37m)	12' MAX. (3.64m)

H +H1 = 20' MAX. (6.2m)

NOTE: V+V1+H +H1= 64' MAX. (19.5m)

Figure 13. Venting with three 90° elbows

Page 15

Image 15

Heat & Glo LifeStyle 36DV manual V Ft, H Ft, VENTING WITH THREE 3 90 ELBOWS, H + H1, Venting with three 90 elbows

Contents

Underwriters Laboratories Listed ModelInstallers Guide Escape-36DVSAFETY AND WARNING INFORMATION THIS UNIT IS NOT FOR USE WITH SOLID FUELPROHIBITED TABLE OF CONTENTS ESCAPE-36DV Service Partsu u u Service Parts List / Liste des pièces de rechangeESCAPE-36DV ACCESSORIES / ACCESSOIRESAppliance Certification Installation CodesHigh Altitude Installations 1Approvals and CodesANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installPreparation2Getting Started Introducing the Heat-N-GloGas FireplacesFigure 1. Diagram of the ESCAPE-36DV Fireplace Dimensions, Locations 3Installing the FireplaceConstructing the Fireplace Chase Step 1. Locating the FireplaceClearance to Hearth Extension Step 2. Framing the FireplaceFigure 3. Framing Dimensions C B ADVP90ST NOTE PIPES OVERLAP 1-1/4INCHES AT EACH JOINTIdentifying Vent Components Step 3. Installing the Vent SystemA. Vent System Approvals TEMS OR COMPONENTS MAY BE USEDFlue Restrictor Instructions STRAIGHT UPVENTING WITH ONE 1 90 ELBOW VENTING WITH TWO 2 90o ELBOWSV FT H + H1 FTV FT V FTH FT VENTING WITH THREE 3 90 ELBOWSVenting Out the Top Vent B. Installing Vent Components3. Install Support Brackets 4. Install FirestopsWARNING THE TERMINATION CAP MUST BE PO C. Vent TerminationFigure 17. Ceiling Firestop Ceiling Side Attic FirestopX = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTEDFigure 20. Vent Termination Minimum Clearances = VENT TERMINALLeveling and Securing of a Fireplace Step 4. Positioning, Leveling andSecuring the Fireplace Figure 22. Proper PositioningWARNING THIS UNIT IS NOT FOR USE WITH SOLID FUEL Step 5. Installing the Optional Heat-ZoneKitHeat-ZoneKit Step 6 The Gas Control SystemNatural Gas Step 7. The Gas Supply LineStep 8. Gas Pressure Requirements PressureWall Switch Step 9. Wiring the FireplaceIntermittent Pilot Ignition IPI Wiring Optional AccessoriesStep 10. Finishing LET/OUTLET GRILLES IN ANY MANNERSealant Material Figure 30. Glass Assembly Step 11. Positioning the Logsand Placing the Ember Material Facing RequirementsReview safety warnings and cautions After the InstallationStep 12. Before Lighting the Fireplace Step 13. Lighting the FireplaceCleaning Flame Sensor Rod IPI Systems Fireplace Maintenance4 Maintaining and Servicing Your Fireplace Cleaning Burner and Controls