Heat Controller, Inc. | Room Air Heat Pump with | Owner’s Manual | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Operating Controls(For Electronic units)
Operating your air conditioner properly helps you to obtain the best possible results.
This section explains proper air conditioner operation.
IMPORTANT:
■If you turn off the air conditioner, wait at least 3 minutes before turning it back on. This prevents the air conditioner from blowing a fuse or tripping a circuit breaker.
■Ddo not trytooperateyourairairconditionerininthethecoolingcoolingmodemode when outside temperatureisisbelow61°F61°F(16°C)(16°C). do. Dnotnottrytryto to operate your air conditioner in the heating mode when operate your air conditioner in the heating mode when outside outside temperature is over 86°F (30°C). Otherwise, the temperature is over 86°F (30°C). The inside evaporator coil inside evaporator coil will freeze up, and the air conditioner will freeze up, and the air conditioner will operate properly. will operate properly.
NOTE: In the event of a power failure, your air conditioner will operate at the previous settings when the power is restored.
Controls
Power Pad
Turns air conditioner on and off.
Display
Shows the set temperature when in Heat/Cool/Energy Saver mode.Shows time remaining on the delay timer. Shows the room temperature when
in Fan Only mode. The Set light will turn on while setting.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
The display shows the set temperature when | Light indicates the unit | |
in Heat/Cool/Energy Saver mode. Shows time | ||
is in the temperature or | ||
remaining on the delay timer. Shows the room | ||
delay time Set mode. | ||
temperature when in Fan Only mode. | ||
|
POWER |
|
|
|
| + |
Power |
|
| Set |
| |
|
| Set |
| ||
|
| Temp / DelayTEMP/TIMER | |||
AUTO | HEAT |
| |||
|
|
|
| ||
Auto | Heat |
|
|
|
|
HIGH | COOL |
|
|
| - |
High | Cool |
|
|
| |
MEd | ENERGY SAVER |
| |||
Med | Energy Saver |
|
|
| |
LOW | FAN ONLY |
|
|
| |
Low | Fan Only |
|
|
|
|
FAN | MOdE | SWING Delay | TIMER | ||
Fan |
|
| |||
SPEEdSpeed | ode |
| |||
|
|
|
| ||
| Light indicates |
| Light indicatesi | the | |
| SWING is on. |
| delay timer is set.. |
Air Conditioner Controls
Delay timer Increase | |
Delay timer |
|
Decrease |
|
Mode select | Auto Fan on |
Fan speed | Fan speed Increase |
Decrease |
|
Temperature | Unit power on/off |
set Increase |
|
and Decrease |
|
Remote Control
Use to set temperature when in Heat (on some models)/Cool/Energy Saver The Set light will turn on while setting.
Press Increase(+) and Decrease
Timer/DelayTimer Increase � (+) /Decrease �
Each touch of the Increase � / Decrease � pads on the unit or the Increase + / Decrease – pads on the remote control will set the delay time when using the
Fan Speed Pads
Use to set the fan speed to Low, Med, High or Auto on the unit. NOTE: On the remote control, use the fan speed Increase + / Decrease – pads to set the fan speeds to Low, Med or High. Use the Auto pad to turn Auto fan on.
Mode Pad
Use to set the air conditioner to Cool, Energy Saver,Fan Only or Heat (on some models) mode.
Timer/DelayPads Pads
24 hours at its previous mode and fan settings.
12