Tools and Supplies Needed | Heatiator CL36D, CR36D specification

F. Tools and Supplies Needed

Before beginning the installation be sure the following tools and building supplies are available:

Reciprocating saw	Framing material
Pliers	Non-combustible sealant
Hammer	Gloves
Phillips screwdriver	Framing square
Flat blade screwdriver	Electric drill and bits
Plumb line	Safety glasses
Level	Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws Misc. screws and nails

G. Fireplace System Requirements

This ﬁreplace system requires:

•Fireplace

•Hearth Refractory

•Grate Assembly

•Hearth Extension (required, sold separately)

•Chimney Air Kit (required in Canada)

•Chimney System (required, sold separately)

•Termination Cap (required, sold separately)

H. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged parts could impair safe operation. DO NOT install dam- aged, incomplete or substitute components. Keep ﬁre- place dry.

•Remove ﬁreplace and components from packaging and inspect for damage.

•Vent system components and doors are shipped in separate packages.

•Report to your dealer any parts damaged in shipment.

•Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and beneﬁt.

Heatilator • CL36D, CR36D • 12538 • Rev V • 05/09

17

Image 17

Heatiator CL36D, CR36D Tools and Supplies Needed, Fireplace System Requirements, Inspect Fireplace and Components

Contents

Fire Risk Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Number Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide Limited Warranty Heatilator CL36D, CR36D 12538 Rev V 05/09 Appliance Certiﬁcation Listing and Code ApprovalsNon-Combustible Materials Combustible Materials Hot glass will cause burns Operating InstructionsYour Fireplace Starting a Fire Seasoned WoodGrate Firescreen Outside Air optional Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional Components Hardwood vs Softwood Wood Fuel Disposal of Ashes Maintenance and ServiceChimney Inspection/Cleaning Check Firebox Refractory Glass CleaningInspect Grate Frequency As desired Start Fire Problems Possible Cause Solution Troubleshooting Guide Typical Fireplace System Getting Started Negative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & Chimney Inspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Framing & Clearances Clearances to Combustible Materials Clearances Mantel Leg or Wall Projections Sidewalls/Surrounds Required Frame the Fireplace Things to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth Strips YES Outside Air Installation Install Outside Air Kit Chimney Assembly Height of Chimney Components Chimney Requirements Example Using Offsets/Returns Assemble Chimney Sections Install Chimney Air KitInstall Ceiling Firestops Mm overlap Install Attic Insulation Shield Cut out Hole in Roof Complete InstallationInstall Flashing Flat Roofs Chimney Termination Requirements Construct the Chase Chase Installations Install Termination Cap Install Fireplace & ChimneyInstall Chase Top ST375 Square Termination Cap Field Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required = 1/k x inches of thickness FinishingHearth Extension In. Micore or equivilent insulation Finishing Material Mantel Combustible Mantel 50 deg 16 3/4 in. Minimum 14-1/2 39 deg 18 in. Min Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1 Reference Materials Fireplace Dimensions Catalog # Chimney Components 14-1/2 10-7/8 276 mm CL36D Service Parts Parts Contact Information