Signal Input, DVI terminal DVI-D | Hitachi 28LD5000TA manual

Signal Input

DVI terminal (DVI-D)

Pin	Input signal	Pin	Input signal
1	T.M.D.S. Data2-	14	+5V Power

2	T.M.D.S. Data2+	15	Ground (for+5V)

3	T.M.D.S. Data2/4 Shield	16	Hot Plug Detect
4	T.M.D.S. Data4-	17	T.M.D.S. Data0-
5	T.M.D.S. Data4+	18	T.M.D.S. Data0+

6	DDC Clock	19	T.M.D.S. Data0/5 Shield

7	DDC Data	20	T.M.D.S. Data5-

8	No Connect	21	T.M.D.S. Data5+

9	T.M.D.S. Data1-	22	T.M.D.S. Clock Shield

10	T.M.D.S. Data1+	23	T.M.D.S. Clock+

11	T.M.D.S. Data1/3 Shield	24	T.M.D.S. Clock-

12	T.M.D.S. Data3-	Frame	GND

13T.M.D.S. Data3+

RGB terminal (D-sub 15-pin connector)

Pin	Input signal

1	R (PR/CR)

2	G or sync on green (Y)

3	B (PB/CB)

4	No connection

5	No connection

6	R.GND (PR/CR, GND)

7	G.GND (Y, GND)

8	B.GND (PB/CB, GND)

9	No connection

10	GND

11	No connection

12	[SDA]

13	H. sync or H/V composite sync

14	V.sync. [V.CLK]

15	[SCL]

1	2	3	4	5	6	7	8
9	10	11	12	13	14	15	16
17	18	19	20	21	22	23	24

5 4 3 2 1

10 9 8 7 6

15 14 13 12 11

•When different kinds of input signals are simultaneously input to the monitor via a graphics board or the like, the monitor will automatically select the signals in the following priority order:

Sync signal type	Priority

H/V separate sync.	1

H/V composite sync.	2

sync.on Green *	3

*Even in the case of the recommended signals shown on the following page, there may be instances when correct display is not possible. In this case, use H/V separate sync, H/V composite sync.

( ) : With component input

S-input connector pin specifications

Pin	Input signal

1	Y

2	Y-GND

3	C

4	C-GND

Frame	GND

3	1
4	2

Scart connector pin specifications

Pin	Signal	Pin	Signal

1	AUDIO OUT (RIGHT)	12	Not Used

2	AUDIO IN (RIGHT)	13	RGB-R GND

3	AUDIO OUT (LEFT/MONO)	14	GND

4	AUDIO GND	15	RGB-R / S.VHS CHROMINANCE IN

5	RGB-B GND	16	BLANKING SIGNAL

6	AUDIO IN (LEFT/MONO)	17	COMPOSITE VIDEO GND

7	RGB-B IN	18	BLANKING SIGNAL GND

8	AUDIO/RGB SWITCH / 16:9	19	COMPOSITE VIDEO OUT

9	RGB-G GND	20	COMPOSITE VIDEO / S.VHS LUMINANCE IN

10	Not Used	21	GND / SHIELD (CHASSIS)

5011 RGB-G IN

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

Image 50

Hitachi 28LD5000TA user manual Signal Input, DVI terminal DVI-D, RGB terminal D-sub 15-pin connector

Contents

28LD5000TA 28 LCD TV Features Contents Safety Instructions About the Symbols Be careful in handling the battery of the remote control Be cautious of the power cord connectionBe sure to keep safety ground connection To Earth Fuse Blue to Neutral Cord Clamp Safety Instructions Do not physically impact the remote control Precautions for the cable connectionPrecaution during transportation Set the sound volume at a suitable level Component Names Main Unit Loading Batteries Remote controlHandling the Remote Control Component Names Remote control Eth Anti-tumble measures Installation InstructionsInstallation Securing to a wall or pillar Connecting to a PC Monitor rear panel English Operating Instructions Turning Power On and OffIndicating Power status Operating Indicating lamp Volume UP/DOWN buttons Operating Instructions Volume AdjustmentInput Switching Audio Mute Display area selection diagram RGB input Size SwitchingInput Signal Screen Display Normal Full Zoom1 Real* Zoom3 Zoom2 On-screen display system Using the Menu ScreenOperating Instructions Press the Return button to return to the previous screen Picture Menu Timer Menu Audio Menu Function Menu Setup Menu Automatic Store Other FeaturesLanguage Menu Select a language by Select buttons and press the OK button When the RGB, RGB2 input is selected Other Features Signal CheckPower Save Mode Status Display Action About residual images About using in a low ambient temperatureAbout screen defects About the panel screen Symptom Point to check TroubleshootingSymptoms That Seemingly Appear to be Failures Check the way the signal cable is connectedPage Troubleshooting Actions to Correct Abnormal Displays With DVI-STB and RGB component setup Connecting to a Video Imaging DeviceAn example of connecting video imaging devices Video Unit Function Display size selection diagram C149L and 149Zoom Using a wide-screen monitorZoom Position + Pictures Split Activating the Split mode from the video input screenOperating Instructions Displaying Multi Picture YNR Operating Instructions Picture Menu Video Power Save Off Default Zoom Panoramic RGB Video Input SystemColour System AV2 1st step Previously recorded items will be lost Output Symptom Point to check SeeDuring VCR special playback fast forward, rewind SUB page buttons Buttons for Teletext ModeTuner Unit funchion Connecting Antenna Precautions when connecting the antenna Auto Full Zoom 149Zoom C149L Input Select button of the monitor or the remote controlDuring TV mode Button Activating the Split mode from the TV screen Pictures Split 4 pictures 12 pictures Display will go out in approximately 6 seconds TV position Sound modePictures Name Split Strobe Picture FreezingFreeze button During TV mode Menu Operating Instructions Setup Menu During Video signal input Bilingual / Dual sound broadcast Other FunctionsA2 / Nicam / Sound Multiplex Stereo sound broadcast Example Operating Instructions Other FunctionsDVD Player Selection Recall button Multiple images sound O.K Symptom Possible reason RemedySnowy picture poor sound Intermittent interference Product Specifications Input connector pin specifications Signal InputRGB terminal D-sub 15-pin connector Scart connector pin specifications Product Specifications Recommended Signal List With R, G, B Video input AV2 and AV4 input Signal mode Horizontal Dot clock RemarksResolution Vertical frequency With component input AV1, AV2 and RGB2-component input This guarantee does not affect your statutory rights