Screw | Hitachi 50V720 guide

Lamp Replacement

6.Without installing the lamp cover, the power will be off and the Lamp Indicator will flash (see page 9). Be sure to install the lamp cover by re-engaging the two clips and tighten the screws before turning the power on, otherwise it may cause unusual colors.

SCREW

LAMP COVER

PHILLIP HEAD

SCREW DRIVER

NOTE: If power is connected before the Lamp Cover is installed, the power will be off and the Lamp Indicator will flash (see page 9).

7.Install the front cover as shown below. Put the front cover back in and align the snap on quick connect then push inwards holding the left and right side of the front cover until you hear a snap. Push the other snap on gently to make a good fit.

8.Plug power cord into AC outlet and turn on the main power switch.

120V

NOTE: This product contains lead and a lamp that contains mercury. Dispose of this product and its lamp in accordance with applicable environmental laws. For lamp recycling and disposal information, go to www.lamprecycle.org. For product recycling and disposal information, contact your local government agency or eRecycle.org (in California), the Electronic Industries Alliance at www.eiae.org (in the US) or Electronic Product Stewardship Canada atwww.epsc.ca (in Canada).

For more information, call “1-800-Hitachi”.

Lamp Replacement

59

Image 59

Hitachi 50V720 important safety instructions Screw

Contents

Useful Information Important Safety Instructions First Time USE Remote ControlLamp Replacement ON-SCREEN Display Read Before Operating Equipment Important Safety Instructions Lead Notice Power sourceModifications Public viewing of copyrighted material Remote Control Battery Installation and Replacement Accessories Viewing How to set up your new Hitachi Projection TelevisionAntenna Location Antenna Connections to Rear Jack Panel Hook-up Cables and Connectors Quick Reference Remote Control Buttons and Functions Side Input Jacks Input Front Panel Controls Lamp Indicator Power LightTemp Indicator Side Panel Jacks and Connections Rear Panel Connections CableCARD Slot TV AS Center Inputs CableCARD Information and press the Select button Additional CableCARD InformationUse the Cursor button VIDEO,Y-PBPRand Hdmi Tips on Rear Panel Connections Speaker placement Connecting External Video Sources Before Operating External Video Source First Connecting a Composite Video Approximately four seconds Input Connecting a Component Remote Control DAY/NIGHT button How to Use the Remote to Control Your TVMode buttons Pause button ZOOM1/ZOOM2 Aspect buttonStandard Expanded Exit button Inputs buttonPICTURE-IN-PICTURE button Menu button White Channel CH Down SUB Picture POP Mode Picture-in-PicturePicture-in-Picture PIP PIP button Picture-In-Picture PIP Modes PIP Mode Picture-in-PictureSplit Mode Picture-in-Picture Surf Mode Picture-in-Picture Strobe Freeze Main FreezeSplit Freeze Cable Brand Codes Remote Control for Cable Box FunctionsOperating the Precoded Function for Your Cable BOX MY Satellite Receiver Remote Control for Set-Top Box/Satelite Receiver FunctionsSatellite Brand Codes SET TOP BOX Brand Codes DVD Brand Codes Remote Control for DVD FunctionsOperating the Precoded Function for Your DVD Player VCR Brand Codes Remote Control for VCR FunctionsOperating the Precoded Function for Your VCR On-Screen Display DRC SRSBBE Video Aspect Mode Black Side Panel Reset Video SettingsVertical Position BBE AudioSRS Internal Speakers Auto Noise CancelPerfect Volume Audio Source DRC LanguageDigital Output PCM Channel Manager Signal MeterSignal Meter Channel List Start or Reset optionAuto Channel Scan Cable or AIR Locks Change Access Code Not Rated Movie RatingsMotion Picture Ratings Table TV Parental Guide Ratings Table TV Ratings Canadian Ratings English Table Canadian Ratings Eng Canadian Ratings French Chart Set The Clock TimersAdjust Clock for Daylight Savings Set Day/Night Timer Set Sleep Timer Select Finish Time HOUR/MINUTE, AM or Set Event TimerEvent 1 , Event 2 , Event 3 , Event 4 and then Select Start Time HOUR/MINUTE, AM or Solid SetupSET the Menu Background Shaded or Set The Inputs Lamp Power Control Caption Display Caption ModeInput 4 Auto Link Set Closed Caption TV Tuner Out Digital CaptionsSet Monitor Out Monitor HDMI1 ANTYES HDMI1 YES Quick Start Up UpgradesUpgrade NOW Insert MMC Card Lamp Life Lamp ReplacementLamp Replacement Lamp Compartment Front Cover 120V Handle Lamp Unit Remove Screws ScrewLamp Cover Phillip Head Screw Driver Screw Do not Equipment Care and TroubleshootingTroubleshooting Switch ON/OFF Reception Problems Inputs Features and SpecificationsFeatures Dimensions Meadowpine Blvd Mississauga, Ontario L5N 6C3 Home Electronics DivisionDigital Media Division Canada 1-800-HITACHI END User License Agreement for Hitachi DTV Software End User Licence Agreement for Hitachi DTV Software Image Input Type Format Aspect Video ID Auto Aspect Appendixes Locks IndexPage Page Page Page Page QR64621