Electrical Requirements and Safety

English

POWER SUPPLY REQUIREMENTS

WARNING

To avoid electrical hazards, ﬁre hazards or damage to the table saw, use proper circuit protection. Always use a separate electrical circuit for your tools. This power tool is wired at the factory for 120V operation. Connect it to a 120V, 15 Amp circuit and use a 15 Amp time delay fuse or circuit breaker. To avoid shock or ﬁre, replace the cord immediately if it is worn, cut or damaged in any way.

EXTENSION CORD REQUIREMENTS

DO NOT MODIFY THE PLUG PROVIDED. If it will not

ﬁt the receptacle, have the proper receptacle installed by a qualiﬁ ed electrician.

IMPROPER CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor (wire) with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a live terminal.

CHECK with a qualiﬁ ed electrician or service personnel if you do not completely understand the grounding instructions, or if you are not sure the saw is properly grounded.

WARNING

Any extension cord must be GROUNDED for safe operation.

MINIMUM GAUGE FOR EXTENSION CORDS (AWG)

Ampere Rating	Volts	Total length of Cord
More Than Not More Than	120V 25ft.	50ft. 100ft. 150ft.

Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole grounding receptacles that accept the saw’s plug. Repair or replace damaged or worn cords immediately.

	240V	50ft.	100ft.	200ft.	300ft.
0	6	18	16	16	14
6	10	18	16	14	12
10	12	16	16	14	12
12	16	14	12	Not Recommended

GUIDELINES FOR EXTENSION CORDS

Any extension cord used for power tools MUST be grounded (3-wire with two ﬂ at prongs and one round ground prong).

Make sure the extension cord is in good condition. When using an extension cord, make sure you use one heavy enough to carry the current the tool will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table above shows the correct size to use according to extension cord length and nameplate ampere rating. If in doubt, use the next heavier gauge cord. The smaller the gauge number the heavier the cord.

NOTE: The 12 to 16 amp rating is correct for this tool. It is highlighted in the table above.

Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualiﬁ ed person before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas. Before connecting the saw to the extension cord, make sure the saw switch is turned OFF.

GROUNDING INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric current and reduces the risk of electric shock. This saw is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into

a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.

sure this is

ected to a n g round.

ng tacle

240V OPERATION

The table saw provided a dual voltage, 120V and 240V, motor. To operate the table saw at 240V, single phase, reconnect the motor wire as the wire wirding on page 74.

WARNING

To avoid injury, disconnect the motor from power source outlet before reconnecting the wire.

To operate the table saw at 240V, replace the 120V plug with a UL/CSA listed plug suitable for 240V (not included) and the rated current of the saw as shown.

Contact your local Hitachi Authorized Service Center or qualiﬁ ed electrician for proper procedures to install the plug. The saw must comply with all local and national electrical codes after the 240V plug is installed. Connect the table saw with 240V plug to a power source outlet as shown.

– 6 –

C 10LA specifications

The Hitachi C 10LA is a powerful and versatile miter saw that stands out in the realm of woodworking and construction tools. Known for its precision, efficiency, and durability, this saw is designed to meet the needs of both professional contractors and DIY enthusiasts.

One of the main features of the Hitachi C 10LA is its robust 15-amp motor, which delivers a remarkable no-load speed of up to 5,000 RPM. This high-speed capability allows users to make clean and accurate cuts through various materials, including hardwood, softwood, and even composite materials. The saw’s large cutting capacity provides a maximum miter cut of 52 degrees to the right and 45 degrees to the left, along with a maximum bevel cut of 45 degrees. This range of motion makes it ideal for creating precise angled cuts, commonly required for crown molding and other intricate woodworking projects.

The C 10LA also features a unique laser marker system that enhances cutting accuracy. This technology projects a laser line onto the workpiece, indicating exactly where the blade will cut, thereby eliminating guesswork and reducing the risk of errors. Additionally, the saw is equipped with a large, sturdy base, providing stability during use and reducing vibration for smoother operation.

Safety is a significant consideration in the design of the Hitachi C 10LA. It includes an electric brake that halts the blade almost instantly after the trigger is released, ensuring that users can operate the saw with confidence. Its dust collector attachment helps maintain a clean work environment by capturing sawdust and debris, which not only improves visibility but also promotes a safer workspace.

The C 10LA’s lightweight design, weighing approximately 26.3 lbs, coupled with a comfortable handle, makes it easy to transport and maneuver, whether in a workshop or on a job site. The saw is also designed for easy blade changes and maintenance, further enhancing its usability and convenience.

In summary, the Hitachi C 10LA miter saw combines powerful performance with advanced features, making it a reliable choice for tradespeople and hobbyists alike. With its high-speed motor, accurate laser guide, impressive cutting capacity, and safety features, it is well-equipped to handle a wide variety of cutting tasks with precision and ease.

Hitachi C 10LA instruction manual Electrical Requirements and Safety

Models: C 10LA

English