Maintenance | Hitachi CB6Y specification

English

MAINTENANCE

GENERAL MAINTENANCE

WARNING

•For your own safety, turn switch OFF and remove the plug from power source receptacle before maintaining, cleaning, adjusting, or lubricating your band saw.

•To avoid fire or toxic reaction, never use gasoline, naphtha, acetone, lacquer thinner or similar highly volatile solvents to clean the band saw.

•To avoid eye injury from blowing debris, wear safety goggles when blowing out sawdust.

BAND SAW

Sawdust will accumulate under the table and base. This could cause difficulty in the movement of the body when setting up a band saw cut, and also cause a fire hazard.

Frequently blow out or vacuum up the sawdust.

Keep your band saw clean. Remove the sawdust from the inside. Vacuum or blow out frequently.

Do not allow filth to build up on the table, the guides, or the support bearings. Clean them with gum and pitch remover. NOTE: Do not immerse the support bearing in the gum and pitch remover.

Put a thin coat of paste wax on the table so that the wood slides easily while cutting.

BLADE WHEEL TIRES

Pitch and sawdust that build up on the tires, should be removed with a stiff brush or scraped off with a piece of wood.

NOTE: To avoid damaging the tires, do not use a sharp knife or any kind of solvent.

When the tires become worn they should be replaced. When replacing the tires, stretch them around the wheels but do not glue them on.

MOTOR

Frequently blow or vacuum out any sawdust from the motor.

WARNING

To avoid electrocution or fire, immediately replace a worn, cut or damaged power cord.

LUBRICATION

All of the bearings are packed with grease at the factory. They require no further lubrication.

BATTERIES

Check the batteries regularly to avoid deterioration. Remove the batteries if you will not be using the worklight for an extended time.

CAUTION: Never put lubricants on the blade while it is spinning.

– 17 –

Image 17

Hitachi CB6Y instruction manual Maintenance

Contents

Hitachi Hitachi Authorized Service Centers NET Weight Product SpecificationsMotor Dust Collection Before Using the Band SAW SafetyGeneral Safety Instructions Power Supply and Motor Specifications Specific Safety Instructions for Band SawsElectrical Requirements Grounding Instructions Minimum Gauge for Extension Cords AWG When using 120 Volt onlyGuidelines for Extension Cords Carton Contents Accessories and Attachments Unpacking Your Band SAW Know Your Band SAW Woodworking Terms Glossary of TermsBand SAW Terms Assembly Instructions Assembly and AdjustmentsEstimated Assembly Time 35 Minutes Tools Needed Miter Gauge Fig. G Installing Blade Fig. FRemoving Blade Fig. E, F Blade Tracking Fig Upper Blade Guide Assembly Fig. JTilting the SAW Fig. H Blade guides Fig. K Upper Blade Guides and Blade Support Bearing Fig. K, LLower Blade Guides and Support Bearing Fig. M, N Blade guides Fig. M Operation ON/OFF Switch Fig. OBasic SAW Operations Support bearing Fig. N Blade Selection Fig. Q Cutting CurvesCircle Cutting Fig. P Maintenance General Troubleshooting GuideProblem Probable Cause Remedy Motor English Moteur Spécifications DU ProduitRécupération DES Copeaux Poids NET Avant D’UTILISER LA Scie À Ruban SécuritéConsignes DE Sécurité Générales Consignes DE Sécurité Spécifiques Pour LA Scie À Ruban Utiliser Uniquement LES Accessoires RecommandésExigences Électriques Alimentation Électrique ET Spécifications DU Moteur Utiliser LA Rallonge Électrique QUI Convient Directives Pour LES Rallonges Électriques’assurer que la rallonge électrique est correctement câblée Calibre Minimal Pour Cordons Prolongateurs Accessoires Recommandés Accessoires ET ÉquipementsContenu DU Carton Déballage ET Vérification DU Contenu Déballage DE LA Scie À Ruban MARCHE/ARRÊT Connaître SA Scie À Ruban Glossaire DES Termes DE LA Scie À Ruban Glossaire DES TermesBouton DE Verrouillage DE Table Verrouille la table Bouton DE Verrouillage DE Guide Supérieur Instructions D’ASSEMBLAGE Installation DE LA Pile DE LA Lampe DE Travail Fig. DAssemblage ET Ajustements Guide À Onglets Fig. G Installation DE LA Lame Fig. FDépose DE LA Lame Fig. E, F GUIDE-LAME Supérieur Fig. J Inclinaison DE LA Scie Fig. HAlignement DE LA Lame Fig Guide-lame Fig. K GUIDE-LAME Supérieurs ET PALIER-SUPPORT DE Lame Fig. K, LPalier-support Fig. L GUIDE-LAME Inférieurs ET Palier DE Support Fig. M, N Sciage DE Base FonctionnementPalier-support Fig. N Interrupteur DE MARCHE/ARRÊT Fig. O Sélection DE Lame Fig. Q Coupe DES CourbesCoupe DE Cercles Fig. P Entretien Problème Cause Probable Action Corrective Guide DE DépannageAjsutement Fonctionnement Moteur Français Motor Especificaciones DEL ProductoFuente de alimentación 120 V, CA, 60 HZ Amperios Antes DE Usar LA Sierra DE Banda SeguridadInstrucciones Generales DE Seguridad USE LOS Accesorios Recomendados Únicamente Requisitos ElectricosEspecificaciones DE LA Alimentacion Electrica Y EL Motor Instrucciones Para LA Conexion a Tierra Cuando se usa 120 voltios únicamente Pautas Para EL USO DE Cables DE ExtensionCalibre Minimo Para Cables DE Extension AWG Contenido DE LA Caja Accesorios Y AditamentosAccesorios Recomendados Desempaque Y Verificacion DEL Contenido Desempaque DE SU Sierra DE Banda Conozca SU Sierra DE Banda Terminos DE LA Sierra DE Banda Glosario DE TerminosInterruptor DE Encendido Y Apagado ON/OFF Manilla DE Fijacion DE LA Mesa Fija la mesa en Instrucciones DE Montaje Montaje Y AjustesTiempo DE Montaje Estimado 35 Minutos Herramientas Necesarias Guia DE Ingletes Fig. G Demontaje DE LA Hoja Fig. E, FInstalacion DE LA Hoja Fig. F Conjunto DE LA Guia DE LA Hoja Superior FIG. J Inclinacion DE LA Sierra Fig. HAlineacion DE LA Hoja Fig Cojinete de soporte Fig. L Guías de la hoja Fig. KCojinete DE Soporte Y Guias DE LA Hoja Inferiores Fig. M, N Guías de la hoja Fig. M Operaciones Basicas DE LA Sierra OperacionCojinete de soporte Fig. N Interruptor DE Encendido Y Apagado ON/OFF Fig. O Seleccion DE LA Hoja FIG. Q Corte DE CurvasCorte Circular Fig. P Mantenimiento Problema Causa Probable Solucion Guia DE Identificacion DE ProblemasIdentificacion DE Problemas DEL Generalidades Motor Model NO. CB6Y Schematic a10″ Band SAW Parts List for Schematic a Parts ListModel NO. CB6Y Always Order by Part NO. and I.D. Number Schematic B Parts List for Schematic B Hitachi Koki Canada Co