Connection to the video signal terminals | Hitachi CP-S830W/E

Connection to the video signal terminals

1. Input signal

S-VIDEO signal			Luminance signal	1.0Vp-p, 75Ω termination
S-VIDEO signal			Chrominance signal	0.286Vp-p (burst signal), 75Ω termination
			Chrominance signal	0.286Vp-p (burst signal), 75Ω termination

VIDEO signal				1.0Vp-p, 75Ω termination

AUDIO signal		Input		200mVrms, 20kΩ below (MAX 3.0Vp-p)

		Output		0~200mVrms, 1kΩ
		Output		0~200mVrms, 1kΩ

2. Signal input terminal

Chrominance signal

Luminance signal

	Ground		Ground
	Ground
		S VIDEO input (Mini DIN4 pin)
Caution	Video input signal terminals have priority in the following order.
Caution
	1 S-VIDEO input terminal	2 RCA jack input terminal

Connection to the RGB signal terminal

1. Input / output signal

	Video signal		Analog 0.7Vp-p 75Ω termination (Positive polarity)

	Horizontal sync signal		TTL level (Positive/negative polarity)

	Vertical sync signal		TTL level (Positive/negative polarity)

	Composite sync signal		TTL level

	Audio signal	Input	200mVrms, 20kΩ below (MAX 3.0Vp-p)

		Output	0~200mVrms, 1kΩ
		Output	0~200mVrms, 1kΩ

2. Signal input / output terminal

1	Video signal (Red)	9	N.C

2	Video signal (Green)	10	Ground

3	Video signal (Blue)	11	N.C

4	N.C	12	DDC (Display Data channel) RGB1 only

5	N.C	13	Horizontal/Composite sync signal

6	Ground (for R)	14	Vertical sync signal

7	Ground (for G)	15	DDC (Display Data channel) RGB1 only

8Ground (for B)

51

106

15 11

D-sub 15pin shrink terminal (Female)

	Caution	Do not use RGB cable other than that specified.
	Caution	Some RGB cable may not operate DDC (Display Data Channel)
		Some RGB cable may not operate DDC (Display Data Channel)
		because there are not connect from pin NO. 15 to pin NO. 12 .

18

Image 18

Hitachi CP-S830W/E specifications Connection to the video signal terminals, Connection to the RGB signal terminal

Contents

Outline FeaturesContents Operating Guide For the Customers in U.K Before use Video signal cablesPower cord Instructions to Users Do not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occurs Handle the power cord carefully Be careful in handling the power cordCleaning Do not step on this unit or do not put a Heavy object on it Do not place this unit where it gets hot When you are not going to use For a long timeClean inside the unit at least once two years Volume Names and functions of each part Main unit RGB output terminal AC in socket Main Power switchRemote control sensor RGB input terminal Video input terminal Remote control transmitter How to insert batteries Replace the cover How to use foot adjusters InstallationExample of the projector and screen installation View from the top Basic operations To project the picture To turn off the power PLUG&PLAY Adjustments and functions To return to the initial settingMemory function SET UP Adjustment Item Details of adjustment Input Image OPT Menu OPT. allows you to control communication function etc Connection to the video signal terminals Connection to the RGB signal terminal Example of computer signal Resolution Standard Display DotsKHz Type Initial set signals Computer/signal Horizontal Timing µs Connection to the control signal terminal Control signal terminal PS/2 mouse ADB Mac mouseSerial mouse Control command table Control command tableCommunication Control data table Procedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command error Example of system setup Connecting various equipment Cleaning the air filter Clean the air filter using a vacuum cleaner How to replace lamp Remove the lamp coverLoosen two screws and pull Handle to remove Lamp.Screw Message table Reset the lamp timeLamp On-screen display When you think something wrong Specifications