2
2
1
1
–12 –EN
Setup
English
Preparation for Use
YES
NO
Hint
Hint
• To go back one step, press Cursors
(during the steps [2] to [7].)
•
Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
Hint
Hint
• If you accidentally select Spanish or
French but need English:Press MENU and
choose SELEC.IDIOMA, or
SELECTION LANGUE.Press
CursorB, and select ENGLISH. Finally,
press CLEAR/C.RESET.
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
1
1
Turn on the TV and set it
to channel 3.
•If channel 3 is already occupied for broadcasting,
see“RF Output Channel”section on page 7.
3
3CH 01
AUTO SET UP
To Add or Delete Channels
1) Press MENU until the main menu
appears.
2)Select “CHANNEL SET UP”by
pressing Cursor Kor L.Then, press
CursorB.
3) Select “MANUAL SET UP”by
pressing Cursor Kor L.Then, press
CursorB.
4) Enter the desired channel number by
pressing Cursor Kor L.
5) Add or Delete it from memory by
pressing Cursor {or B.so that
“ADD”or “DELETE”flashes on the
TV screen accordingly.
6) Exit the preset mode by pressing
CLEAR/C.RESET.
To Preset the Channel Again
1) Press MENU until the main menu
appears.
2)Select “CHANNEL SET UP”by
pressing Cursor Kor L.Then, press
CursorB.
3) Select “AUTO SET UP”by pressing
CursorKor L.Then, press
CursorB. After scanning, the tuner
stops on the lowest memorized
channel.
To Change the On-Screen Language
1) Press MENU until the main menu
appears.
2) Select “LANGUAGE SELECT”by
pressing Cursor Kor L.Then, press
CursorB.
3) Select “ENGLISH”, “FRANCAIS”or
“ESPAÑOL”by pressing CursorKor
L.Then, press CLEAR/C.RESET.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
•
You can select only the channels memorized in
this unit by using SKIP/CH(i/Kor j/L).
•If “AUTO SET UP”appears on the TV
screen again, check the cable connections.
Then, press CursorBonce again.
Y
Yes
es Press MENU
to exit
• Refer to “Hint for Cable Box or
Satellite Box”section on page 7.
Do you connect the cable from the cable box or
the satellite box to the VCR/DVD’s ANT IN jack?
Turn on the unit for the first
time
Clock Set Up
To Select a Channel
You can select a channel by directly
entering channel using
the Number buttonson the remote
control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example:117, press 1,1,7)
• You must precede single-digit channel
numbers with 0 (For example:02, 03,
04 and so on).
5
5
4
4CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 2 0 0 5
HOUR MINUTE AM/PM
– – : – –– –
CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE AM/PM
0 5 : – –– –
6
6CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 – –
7
7CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 TUE 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 P MAM
BPM
Select the current year
Select “AM”or “PM”
8
8 To exit the CLOCKSET
screen.
Select the current hour
Select the current minute
press first.
VCR
-MENU-
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
BCLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
MENU
• If the clock is not set, the
CLOCK SET screen
appears when you press
MENU.In this case, go
to step [2].
press first.
VCR
*
Refer to page 11 to switch between the VCR/DVD modes.
To select the desired language
To decide
To decide
To decide
To decide
To decide
2
2CLOCK SET
MONTH DAY YEAR
0 3 / – –– – – –
HOUR MINUTE AM/PM
– – : – –– –
3
3CLOCK SET
MONTH DAY YEAR
0 3 / 1 5 – – – –
HOUR MINUTE AM/PM
– – : – –– –
Select the current month
Select the current day
To decide
To decide
or
or
or
or
or
or
or
or
or
CLEAR
C.RESET
LANGUAGE SELECT
BENGLISH [ON]
FRANCAIS
ESPAÑOL
H9850UD_EN/SP.qx3 05.4.8 11:42 AM Page 12